Gaggenau 200 Serie Notice D'installation page 20

Securing the seal
Secure the enclosed seal on the flat duct elbow at
▶
a maximum of 5 mm from the edge.
→ Fig.
42
Establishing the piping
Insert the flat duct elbow into the outlet opening
1.
on the rear of the appliance.
→ Fig.
43
If required, install additional piping elements.
2.
Inserting the appliance into the worktop cut-out
Ensure that the connection cable is connected to
1.
the appliance.
Carefully insert the appliance into the worktop cut-
2.
out.
→ Fig.
44
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
39
Connecting the exhaust air pipe
Secure the exhaust air pipe to the flat duct bend.
1.
Establish the connection to the exhaust air open-
2.
ing.
Seal the joints appropriately.
3.
Aligning the appliance in the worktop cut-out
Use the enclosed spacers to adjust the circumfer-
1.
ential gap between the appliance and the worktop
to a uniform distance of 1.5 to 2 mm.
→ Fig.
38
Remove the spacers before sealing the join.
2.
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
Observe the filters' air flow direction.
1.
Insert two of the filters into the left and right of the
2.
appliance, and slide them forwards.
→ Fig.
48
Insert the other filters into the left and right of the
3.
appliance.
→ Fig.
49
Inserting grease filters
Insert the grease filter.
▶
Establishing the connection to the power
supply
Observe the connection data on the rating plate.
1.
For 3 N, connect the cable to the mains socket in
2.
accordance with the figure.
→ Fig.
50
For 2 N, connect the cable to the mains socket in
3.
accordance with the figure.
→ Fig.
51
For 1 N, connect the cable to the mains socket in
4.
accordance with the figure.
→ Fig.
52
For 2 L/2 N, connect the cable to the mains
5.
socket in accordance with the figure.
→ Fig.
53
Note the colours of the cables.
6.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
20
– GY: Grey
If required, arrange the supplied wire end ferrules
7.
differently depending on the type of connection.
To connect two cables, if required, use a wire end
8.
ferrule.
Shorten the wires.
‒
Remove the insulation.
‒
Checking the function
Switch on the appliance.
1.
If , or lights up, the appliance is not
2.
connected correctly. → "Checking and correcting
the electrical connection", Page 20
If no faults appear in the appliance's display, use
3.
the operating instructions to check that the ventila-
tion is working.
Checking and correcting the electrical connection
Disconnect the appliance from the power supply.
1.
Check whether the connection to the appliance
2.
(fig. 4) and the building-side connection (fig. 8)
correspond to the connection diagram in these in-
stallation instructions. → "Preparing the electrical
connection", Page 17 → "Establishing the connec-
tion to the power supply", Page 20
For 3 N, observe the following figure.
3.
→ Fig.
54
For 2 N, observe the following figure.
4.
→ Fig.
55
For 1 N, observe the following figure.
5.
→ Fig.
56
Sealing crevices
Requirement: You must carry out a function test be-
fore sealing the joint.
Seal the gap around it using suitable, heat-resist-
1.
ant silicone, e.g. Novasil® S70 or Ottoseal® S70.
→ Fig.
57
Unsuitable silicone adhesive causes permanent
discoloration to natural stone worktops.
Use the smoothing agent recommended by the
2.
manufacturer to smooth the crevice.
Observe the usage instructions for the silicone ad-
3.
hesive.
Leave the silicone adhesive to dry for at least 24
4.
hours.
The drying time depends on the ambient temper-
ature.
Do not operate the appliance until the silicone has
5.
dried completely.
Switching the display for air extraction
mode
If required for the air extraction mode and the air
1.
recirculation mode, change the display of the elec-
tronic control in the basic settings.
Observe the basic settings section in the instruc-
2.
tion manual.
Removing the appliance
ATTENTION!
Tools may damage the appliance frame.
Do not prise out the appliance from above.
▶
Disconnect the appliance from the power supply.
1.
Remove the exhaust air duct or undo the circulat-
2.
ing-air connections.
Remove the silicone joint.
3.
Push out the appliance from below.
4.