Gaggenau 200 Serie Notice D'installation page 19

After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
30
Preparing the unit for air extraction mode
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with a flat duct elbow for the cut-out in the back
wall.
→ Fig.
33
After making the cut-outs, remove any shavings.
3.
Seal the cut surfaces so that they are heat-resist-
4.
ant and waterproof.
→ Fig.
30
Attaching adhesive tape
Attach the enclosed adhesive tape to the worktop
▶
section.
→ Fig.
34
Installing the appliance
WARNING ‒ Risk of injury!
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
Wear protective gloves
▶
The appliance is heavy.
To move the appliance, two people are required.
▶
Use only suitable tools and equipment.
▶
Install the appliance for air extraction mode
▶
→ Page 19, circulating-air mode → Page 19 or
circulating-air mode with circulating-air duct
→ Page 19.
Note: The appliance is only intended for flush install-
ation.
Installing the appliance for circulating-air mode
with adapter
Note: When installing directly on an outer wall that is
not thermally insulated or above a cold floor
(µ ≥ 0.5 W/m² °C), we recommend a configuration
with a circulating-air duct.
For the circulating-air mode, use the adapter and
1.
the odour filter.
Ensure that the clearance between the appliance
2.
and the rear panel of the unit is between 10 and
80 mm.
Attaching the adapter
Clean and degrease the adhesive surface around
1.
the cut-out in the unit's back panel.
Insert the adapter into the outlet opening on the
2.
rear of the hob.
→ Fig.
35
Remove the adhesive tape's protective film from
3.
the adapter.
→ Fig.
36
Inserting the appliance into the worktop cut-out
Ensure that the connection cable is connected to
1.
the appliance.
Carefully insert the appliance into the worktop cut-
2.
out.
→ Fig.
37
Aligning the appliance in the worktop cut-out
Use the enclosed spacers to adjust the circumfer-
1.
ential gap between the appliance and the worktop
to a uniform distance of 1.5 to 2 mm.
→ Fig.
38
Remove the spacers before sealing the join.
2.
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
39
Securing the adapter
Hold the adapter at the central holder and use the
1.
side holders to slide it towards the unit's back
panel in the base unit, then affix it.
→ Fig.
40
If required, also use screws to secure it.
2.
→ Fig.
41
Installing the appliance for air recirculation mode
with circulating-air duct
For circulating-air mode, use the seal, the circulat-
1.
ing-air duct, the diffuser and the odour filter.
Observe the dimensions for the different flat duct
2.
bends. → Page 16
Securing the seal
Secure the enclosed seal on the flat duct elbow at
▶
a maximum of 5 mm from the edge.
→ Fig.
42
Inserting the flat duct elbow
Insert the flat duct elbow into the outlet opening
▶
on the rear of the appliance.
→ Fig.
43
Inserting the appliance into the worktop cut-out
Ensure that the connection cable is connected to
1.
the appliance.
Carefully insert the appliance into the worktop cut-
2.
out.
→ Fig.
44
Aligning the appliance in the worktop cut-out
Use the enclosed spacers to adjust the circumfer-
1.
ential gap between the appliance and the worktop
to a uniform distance of 1.5 to 2 mm.
→ Fig.
38
Remove the spacers before sealing the join.
2.
Establishing the pipework between the appliance and
the diffuser
Connect the components of the circulating-air duct
1.
to each other.
Secure the flat duct pipe connector by enga-
‒
ging it in place.
For an additional fixing, screw the flat duct pipe
‒
connector together using 4 x PT 4x8 mm
screws for plastic.
→ Fig.
45
Connect the circulating-air duct to the flat duct el-
2.
bow on the rear of the hob.
→ Fig.
46
Connect the diffuser to the circulating-air duct.
3.
→ Fig.
47
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
39
Install the appliance for air extraction mode
For air extraction mode, use the seal and the
1.
acoustics filters.
Observe the instructions for the exhaust air pipe.
2.
→ Page 18
19