Publicité
Les langues disponibles
Les langues disponibles
Intended Use
Rotary multi tool with flexible shaft for intricate grinding, polishing, sanding, drilling and cutting
applications in domestic craft work
Unpacking Your Tool
• Carefully unpack and inspect your new tool. Familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
GB
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Collet installation
WARNING: ALWAYS fit the correct collet that precisely matches the shaft diameter of the
accessory you wish to use.
Note: This hobby tool is supplied with four Collets (2) in order to fit accessories with different shaft
diameters (see 'Specification').
1. Remove the Collet Nut (1) by depressing the Spindle Lock Button (4) and rotating it
anticlockwise until it can be removed from the spindle
Note: It may be necessary to use the supplied Collet Spanner to loosen the Collet Nut.
2. Remove the brass Collet, and replace with a Collet of the required size
3. Refit the Collet Nut, depress the spindle lock button and rotate the Collet Nut clockwise, to
secure it on the spindle
Changing accessories
WARNING: Ensure the tool is switched off and disconnected from the power supply before
fitting or removing accessories.
1. Loosen the Collet Nut (1) by depressing the Spindle Lock Button (4) and rotating the Collet Nut
anticlockwise
Note: It may be necessary to use the supplied Collet Spanner to loosen the Collet Nut.
2. Place the accessory required into the Collet (2)
WARNING: Ensure the correct Collet for the accessory shaft diameter has been fitted.
3. Depress the Spindle Lock Button and rotate the Collet Nut clockwise to secure the accessory
in the Collet
WARNING: Never fit an attachment with a maximum speed lower than the no load speed of
the machine.
Fitting a sanding sleeve
1. Loosen the small screw in the top of the rubber drum (accessory pack) so that the rubber
slackens
2. Slide the sanding sleeve (accessory pack) onto the drum
3. Retighten the screw so that the sanding sleeve is secured in position (do not over-tighten)
Fitting a cutting/sanding disc
1. Loosen the Collet Nut (1) and insert the cutting/sanding disc mandrel into the Collet (2). Re-
tighten the Collet Nut to secure in position
2. Use the spanner to remove the fixing screw from the end of the cutting/sanding disk mandrel
3. Thread the screw through the centre hole of the cutting/sanding disc, then screw the fixing
screw back into the mandrel to secure the cutting/sanding disc in position for use (do not
over-tighten)
Attaching the flexible shaft
Note: The 3.2mm Collet (2) will need to remain in the tool in order to secure the Flexible Shaft's
(9) inner cable. Securing the cable in place remains the same process as securing an accessory in
the tool. An additional 3.2mm Collet is included.
1. Remove the Collet Cover (3)
2. Depress the Spindle Lock Button (4) and loosen the Collet Nut (1) using the supplied Collet
Spanner
3. Insert the inner cable of the Flexible Shaft (9) as far as it will go into the Collet (2)
4. Re-tighten the Collet Nut (1) to secure the cable
5. Rotate the Shaft Lock Ring (10) clockwise to thread it onto the tool housing. Hand tighten only
6. Pull back the collet cover at the opposite end of the flexible shaft to expose the collet
7. Use the spanner in the way described in 'Changing accessories' to fit an accessory beneath
the Shaft Collet Nut (11)
WARNING. When operating, do not bend the flexible shaft to a radius of less than 150 mm (6").
Store the flexible shaft carefully when not in use
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as
well as suitable gloves, when working with this tool.
Switching on and off
1. Start the hobby tool by moving the On/Off Switch (8) to the 'I' position
2. Stop the tool by moving the switch to the '0' position
Adjusting tool speed
WARNING: ALWAYS set the speed according to the requirements of the accessory fitted and
the material of the workpiece.
• Use the Variable Speed Dial (6) to control the rotation speed
Note: The higher the number on the dial the faster the spindle rotates.
Handling
WARNING: Always ensure the workpiece is adequately secured using clamps and/or a vice at all
times. Do not attempt to use this tool without sufficiently securing the workpiece first.
• Hold the tool securely, keeping hands well away from rotating parts. For most purposes, it is
most convenient to grip the tool as though it is a pen
• If possible hold the tool with both hands when performing cutting operations
• Practice using the tool with scrap material before starting a job. Be aware that different
accessories will require different techniques, and may require different speed settings
• Applying excess pressure does not result in faster or more efficient performance. If the
pressure applied to the tool has a noticeable effect on the speed of the tool then reduce the
pressure. Overloading the tool will reduce its service life
• Always ensure that material is secure. If appropriate use a vice or clamp to hold the work
Accessories
• A range of accessories and consumables, including Rotary Tool Accessory Kit 216pce, Rotary
Tool Telescopic Hanging Stand, and Panoramic Safety Goggles, is available from your GMC
stockist. Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised GMC service centre. This advice also applies to extension cords
used with this tool
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
8
Publicité
