Renkforce RF-PCR-550 Mode D'emploi page 3

Operating Instructions
RF-PCR-550
Portable card reader with SSD enclosure
Item No. 2299886
Intended use
Use the product to:
• read and write data from/to memory cards;
• read and write data from/to an SSD drive;
• transfer data via USB ports;
• transfer visual content to a display device via HDMI port;
• charge or operate a compatible device via Power Delivery (PD);
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-
rooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can result in short circuits, fires, or other hazards.
Read the instructions carefully and store them in a safe place. Make this product available to
third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
See overleaf for connection and operation details.
Delivery content
• Enclosure
• USB-C cable (30 cm)
TM
• Rubber feet
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about the operation, safety or connection of
the appliance.
• Screws (1x large, 4x small)
• Screw driver
• Operating instructions
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Operating elements
1
2
3
4
1 SSD indicator light
2 Power indicator light
3 USB-C main port (e.g. computer)
TM
4 USB-C PD (Power Delivery) input port
TM
Installing an SSD drive
Requirements:
• Size: M.2 2280 / Capacity: max. 2TB
NOTICE
Prevent product damage! Remove electrostatic discharge from yourself before touch-
ing and handling electronic components.
1. If screws are installed at the bottom of the enclosure, remove them. Use a suitable screw-
driver.
2. Slide the board out of the case as shown in the section "Operating elements". Mind the
direction; it only slides out one way.
3. Connect the SSD drive to the M.2 connector. Secure the drive with the supplied large screw.
4. Carefully slide the board back into the case.
5. Secure the board through the bottom with the 4 screws.
Technical data
USB-C main port ....................... Input: 5 V/DC, max. 3 A
TM
Power delivery port (PD) .............. max. 20 V/DC, 5 A, 100 W (PD)
USB 3.0 ports ............................... Data transfer: max. 5 Gbps
Power supply: 5 V/DC, max. 1.5 A (shared by both ports)
microSD/SD card .......................... Capacity: max. 128 GB / Transfer rate: max. 104 MB/s
SSD drive ..................................... Size: M.2 2280
Capacity: max. 2TB
Transfer rate: max. 6 Gbps
HDMI ............................................ 3840 x 2160, 30 Hz
Operating system support ............ Windows
Ubuntu 16.04 LTS and higher / Android 5.0 and higher
Operating conditions ..................... 0 to +40 ºC, 10 – 90 % RH (non-condensing)
Storage conditions ........................ -40 to +70 ºC, 10 – 90 % RH (non-condensing)
Dimensions ................................... 127 x 12 x 57 mm (W x H x D)
Weight .......................................... approx. 98 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
8
7
6
5
5 microSD/SD card slots
6 HDMI port (receiver)
7 USB 3.0 ports
8 M.2 connector (SSD drive)
7/8/10 and higher / MacOS 10.0 and higher
®
*2299886_v1_1020_02_jh_m_4L_(1)