Publicité
Les langues disponibles
Les langues disponibles
should firmly hold the machine during work. Mill-
ing cutter with appropriate dimension shall be
used. Anytime when the milling cutter is used or
changed, it must be ensured that switch on the ma-
chine is on off position� In order to avoid personal in-
jury done to you and your bystanders, the power lines
must be pulled out of the socket when the milling cutter
is assembled or changed�
• When the machine is used, you will work in
dusty environment; therefore, you should wear
mask and goggles. If you have long hair, you shall
wear hair care cap� You shall not wear loose clothes
during work�
• If the power lines are damaged, you shall not
touch them. It is prohibited to use any machine
with damaged power lines� The power lines must be
placed behind the frame (tool operation shall not be
affected)�
• The machine shall be operated in rain or humid
environment. You shall not touch the power lines to
avoid fire or electric shock�
• Before the machine is removed from the work-
piece, you shall cut off power switch and com-
pletely stop the milling cutter.
• The hands shall always be far away from the ro-
tating parts. When the milling cutter is in contact with
the workpiece, you shall not make an attempt to start
the machine�
• After work, the switch shall be turned off first
and then lock knot of guide pillar shall be loosed
to make the machine return to original position.
Safety guidelines during
power tool operation
Before commencing operation
• During machining, do not place the workpiece on
a sturdy surface (concrete, steel, stone, etc�) - when
the router bit passes through the workpiece, you can
damage the router bit and lose control over the power
tool�
• Use the router bits whose allowable rotary speed
does not exceed the rotary speed of the power tool
spindle� Observe manufacturer's recommendations
for router bits use� Do not use router bits that do not
conform to the specifications included in the user's
manual�
• Use only sharp nondefective router bits� Bended,
blunt or cracked router bits must be replaced�
• The router bit shank diameter must match precisely
with the internal diameter of the power tool collet�
• Never use the router bit if its cutting unit diameter
exceeds the diameter of the hole in the base plate�
• Remove all nails or any other metal objects from
blanks before cutting�
• When making cuts in walls or partitions, it is nec-
essary to find the location of hidden wiring, water-
pipes and gas pipes� Severe injuries may occur as a
result of damaging electric wiring or household utility
lines�
During operation
• Keep your hands at a safe distance from the rotat-
ing router bit� Remember that when machining a work-
piece, the router bit end occasionally protrudes beyond
the lower part of the workpiece and is not protected -
touching it may cause severe injuries� Never touch the
rotating router bit with your hands�
• Never start the machining until the router bit reaches
its full speed�
• Advance the router bit to the workpiece only with the
power tool turned on, otherwise the router bit may be
pinched in a workpiece, or a recoil and loss of control
over the power tool can occur�
• When processing small blanks, use clamping devic-
es. If the blanks are too small to be fixed properly - do
not process them�
• Never remove sawdust while the power tool motor
is running�
• Do not work materials containing asbestos� Asbes-
tos is considered carcinogenic�
• Avoid stopping an electric tool motor when load-
ed�
• Avoid overheating your power tool, when using it for
a long time�
• Never operate the power tool over your head level�
After finishing operation
• The power tool may be removed from the workplace
only after it is turned off and the router bit stops com-
pletely�
• Decelerating the router bit rotation by inertia using
the spindle keylock is strictly forbidden- this will put the
power tool out of operation and void your right to the
warranty service�
• During operation the router bit runs very hot - do not
touch it until it cools down�
• Cleaning of the workplace after work should be per-
formed by persons equipped with the aforesaid per-
sonal protection means�
Warning: the chemical substances con-
tained in dust generated in sanding,
cutting, sawing, grinding, drilling and
other construction industry activities
may result in cancer, congenital deficiency or be
harmful to the fertility. The ion of some chemical sub-
stances shall be:
• Before any repair and replacement work to the ma-
chine, the power plug must be pulled out firstly.
• The transparent two silicon oxide and other ma-
sonry products in the wall bricks and cement; the
chromium arsenic (CCA) in wood with chemical treat-
ment� The harm degree of these substances shall
depend on the frequent degree of you carrying out
these works� If you want to reduce the contact with
these chemical substances, please work in the place
with ventilation and you shall use the appliances with
safety certificates (such as the dust mask designed
with tiny dust filter).
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same to
the voltage marked in the tool's data plate� If the power
voltage is higher than the appropriate voltage, the acci-
dents will be resulted to the operators, and at the same
time, the tool will be destroyed� Therefore, if the power
voltage has not been confirmed, then you shall never
plug in arbitrarily� On the contrary, when the power
voltage is lower than the required voltage, the motor
will be damaged�
English
20
Publicité
