ViM KUBAIR F400 ECOWATT CC Notice Technique page 21

Register Address
0x0014 13
0x0014 14
0x0016 15
0x0017 16
0x0018 17
0x0019 18
0x0020 19
0x0021 20
0x0022 21
0x0023 22
0x0024 23
0x0031 30
5.3.2 Input Stat Bits
Les Input Stat Bits disponibles sont indiqués dans le tableau ci-dessous.
Input Stat Bits: 29 (R)
0x02: Read
Register Address
1x0001 0
1x0002 1
1x0003 2
1x0004 3
1x0005 4
1x0006 5
1x0007 6
1x0008 7
1x0009 8
1x00010 9
1x00011 10
1x00012 11
1x00013 12
1x00014 13
1x00015 14
1x00016 15
1x00017 16
1x00018 17
1x00019 18
1x00020 19
1x00021 20
1x00022 21
1x00023 22
1x00024 23
1x00025 24
1x00026 25
1x00027 26
1x00028 27
1x00029 28
* Uniquement si l'une des fonctions de sortie de l'IOM est activée.
Function
Allow using Brake Chopper
Allow using Cooling Fan
3 x 230V config
1V start voltage
Very High Switch Frequency
Write protect config
Clear PowerLog (Wh, kWh, MWh)
Motor output off
Show alarm-type with LED-blink
Autodetect Control mode
Set Output Pin (If Output Cfg=5)
Analog Firemode
Function
V LO Alarm
V HI Alarm
I HI Alarm (Motor out short)
Temperature High
Input Phase Error
Rotor Blocked
Current Limit
Voltage Limit
Rotor Direction
EEPROM Error
Internal Stop
Earth fault (H5 only)
Brake Chopper Fault
Motor Phase Error
Communication error MOC
V Ripple
Digital Input 1
Digital Input 2
Ext. 24V supply overload
MOC in bootloader
Digital Input 3 (IOM)
Digital Input 4 (IOM)
Communication error IOM
Motor Overheat (IOM)
Windmilling
Rotation OK
IO Config mismatch
Config write attempt
Unsaved UserData
Range
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
Range
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
21/60 NT00000631-KUBAIR-F400-ECOWATT-FR-210623
Active state
1 = Allow BC
1 = Allow Fan
0 = Voltage values from CCF
1 = Fixed values for 3 x 230V
0 = Start @ 2V
1 = Start @ 1V
0 = 8 kHz as "HI SF"
1 = 10 kHz as "HI SF"
0 = Allow change via Modbus
1 = "Lock" configuration
1 = Clear Power Log
1 = Keep motor output off
1 = Use blink to show alarm
1 = Analog control with temporary
Modbus override
0 = Output "Low", 1 = "High"
1 = active
Active state
1 = Alarm
1 = Alarm
1 = Alarm
1 = Warning
1 = Warning
1 = Alarm
1 = Warning
1 = Warning
1 = Alarm
1 = Warning
1 = Alarm (Stop)
1 =Alarm
1 = Warning
1 = Alarm
1 = Alarm
1 = Warning
1 = HI
1 = HI
1 = Overload
1 = Alarm
1 = HI*
1 = HI*
1 = Warning*
1 = Alarm
1 = Warning
1 = OK
1 = Warning
1 = Detected
1 = Unsaved