Assembly & Installation - Cub Cadet 19A30031100 Manuel De L'opérateur

NOTE: Before performing any of the instructions throughout this manual, references to left,
right, front and rear of the tractor are from the operator's position, unless otherwise stated.
• Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop
the tractor engine and set the parking brake.
• For convenience, pivot the seat forward and leave it in that position until the grass
collector is fully mounted and assembled.
Assemble Mounting Brackets
To assemble the universal mounting
assembly, locate the rider hitch bracket
assembly (689-00304A) and the universal
support bracket (783-08129) and follow
these steps:
1. Attach the two hitch side brackets
to the rear support bracket
(rider hitch bracket assembly
689-00304A) using two carriage
bolts (710-0276) and wing knobs
(720-04122) from hardware pack
689-02364. See Figure 1.
NOTE: The hooks on the side
brackets should point downwards
and the tabs on the rear plate point
upwards as shown in Figure 1.
2. Flip over assembly and mount the
hitch support bracket to the
universal support bracket (783-
08129) using two carriage bolts
(710-0276) and wing knobs (720-
04122) from hardware pack 689-
02364. See Figure 2.
NOTE: It might be easier during the mounting stage to leave this hardware only finger tight
to facilitate lining up the hitch hole for the clevis pin. You will be instructed to tighten this
hardware later in this manual.
NOTE: Use the two holes closest to the
cross mount, see Figure 2. The hitch
support bracket will need to be flipped to
enable alignment of the proper holes.
Mount Assembly on Tractor
1. Place the hooked ends of the
mounting assembly over the
shoulder bolts on the back of the
tractor frame and line up the hitch
support bracket center hole with
the hole on the tractor's hitch. See
Figure 3.
2. Install the clevis pin (711-0309A)
from hardware pack 689-02364
into the tractor's hitch and secure
with a cotter pin (714-0117).
See Figure 4.
ASSEMBLY AND INSTALLATION
Figure 1
For All Other Models
Knob Hole Position
Figure 2
Figure 3
Align hole on
bracket with hole
on tractor
Figure 4
NOTE: The clevis pin can be fed down through the hitch plate and secured underneath with
the cotter pin, or it may be easier to feed the clevis pin up through the hitch plate hole and
secure with the cotter pin on the topside. Insert the cotter pin into the top hole, closest to
the head of the pin. You may need to push up on the pin to make the hole accessible.
IMPORTANT ! If you decided to leave the
hitch support only finger tight during the
assembly process, tighten all of the
hardware securely at this time.
Mount Vertical
Support Bracket
1. Install the vertical support bracket
onto the mounting assembly on the
tractor by hooking it over the cross
mounting bracket. See Figure 5.
2. Align the vertical support bracket
with the hole that best suits the
deck size of your tractor.
3. Secure the vertical support bracket
to the cross mounting bracket using
a carriage bolt (710-0276) and wing
knob (720-04122) from hardware
pack 689-02364. See Figure 6.
NOTE: Position "C" is the recommended
mounting position, but you may use other
mounting positions to accommodate
other attachments.
Install Hanger Assembly
1. Install and secure hanger assembly
onto the vertical support bracket
using two carriage bolts (710-
0276), two cup washers (736-0242)
and two lock nuts (712-04063)
from hardware pack 689-02364.
See Figure 7.
Assembling Remaining
Bagger Components
1. Tilt the front of the upper chute
support slightly forward. Slide the
clip behind the tab, then snap the
front latch to the rail, as shown in
(1) of Figure 8.
2. Snap the upper chute support in
place by first clipping the side
portion onto the hanger assembly
rail. See (2) in Figure 8.
3. Slide the left grass catcher cover
over the upper chute support and
the hanger assembly rail. Carefully
latch the two tabs in place into the
front of the upper chute support,
see (1) in Figure 9.
4. Fit the snaps onto the left side
hanger assembly rail. See (2) in
Figure 9.
6
38" Deck
42" Deck
46" Deck
A B C
Figure 5
Figure 6
Figure 7
2
1
Figure 8
1
1
2
Figure 9