Hornby Hobbies jouef HJ2268 Guide Rapide page 5

27 Brake modus Allowed brake modus
Bit
0
1
2
3
4
28 RailCom confi guration Settings for RailCom
®
Bit
0
1
7
29 Confi guration register The most complex CV within the DCC standards. This register contains important information, which is only relevant in DCC
mode.
Bit
0
1
2
3
4
5
31 Index register H Selection page for CV257-512
32 Index register L Selection page for CV257-512
49 Extended confi guration Activate support for brake sections or switch off Back EMF control
Bit
0
1
2
3
4
5
6
50 Analogue mode Selection of allowed analogue modes
Bit
0
1
52 Load control parameter «K» "K"-component of the internal PI-controller for the low speed steps. Defines the effect of load control. The higher the value, the
for slow driving stronger the effect of Back EMF control.
53 Control Reference voltage Defi nes the Back EMF voltage, which the motor should generate at maximum speed. The higher the effi ciency of the motor, the
higher this value may be set. If the engine does not reach maximum speed, reduce this parameter.
54 Load control parameter K "K"-component of the internal PI-controller. Defines the effect of load control. The higher the value, the stronger the effect of
Back EMF control.
55 Load control parameter I "I"-component of the internal PI-controller. Defines the momentum (inertia) of the motor. The higher the momentum of the
motor (large flywheel or bigger motor diameter, the lower this value has to be set).
56 Operating range of load 0 - 100% Defi nes up to which speed in % load control will be active.
control A value of 32 indicates that load control will be effective up to half speed.
63 Sound volume Volume of running and additional sounds.
124 Extended Confi guration #2 Additional important settings for LokSound Decoders
Zusätzliche wichtige Einstellungen der LokSound-Decoder
Bit
0
1
2
4
125 Starting voltage Analog DC
126 Maximum speed Analog DC
127 Starting voltage Analog DC
128 Maximum speed Analog DC
Function
ABC brakes, voltage higher on right side
ABC brakes, voltage higher on left side
ZIMO HLU brakes active
Brake on DC, if polarity is vice-versa to the driving direction
Brake on DC, if polarity is the same as driving direction
®
Function
Channel 1 given free for address broadcast
Data connection on channel 2 allowed
RailCom ® Plus automatical loco registration active
Function
Normal direction of travel.
Forward becomes reverse.
14 speed steps (only in DCC mode).
28 or 128 speed steps (only in DCC mode).
Analogue mode off.
Analogue mode permitted.
RailCom ® switched off
RailCom ® allowed
Speed curve through CV 2, 5, 6.
Speed curve through CV 67 - 96V.
Short addresses (CV 1) in DCC-mode.
Long addresses (CV 17+18) in DCC-mode
Function
Load control off
Load control activated
DC motor PWM frequency - 15 kHz pulse frequency
DC motor PWM frequency - 30 kHz pulse frequency
Märklin ® delta mode - Delta mode off
Märklin ® delta mode - Delta mode on
Märklin ® second address off
Märklin ® second address on
Automatic speed step detection
DCC speed step detection off
Disable LGB function button mode
®
Enable LGB ® function button mode
Disable Zimo ® Manual Function
Enable Zimo ® Manual Function
Function
Disable AC Analog Mode
Enable AC Analog Mode
Disable DC Analog Mode
Enable DC Analog Mode
Function
Disable driving fi rection
Bi-directional bit: Enable driving direction when shifting direction
Disable decoder lock with CV 15/16
Enable decoder lock with CV 15/16
Disable serial protocol for C-Sinus
Enable serial protocol for C-Sinus
Adaptive regulation frecuency
Constant regulation frecuency
Value
1
2
4
8
16
Value
1
2
128
Value
0
1
0
2
0
4
0
8
0
16
0
32
16
0, 2, 3
0 - 255
Value
0
1
0
2
0
4
0
8
0
16
0
32
0
64
0 - 3
Value
0
1
0
2
0 - 255
0 - 255
0 - 255
1 - 255
1 - 192
0 - 192
Value
0
1
0
2
0
4
0
16
0 - 255
0 - 255
0 - 255
0 - 255
Service Sheet HJBD-16
2013 - Subject to technical modifi cations
0
131
14
16
0
19
03
48
140
48
32
255
192
21
90
130
90
130