Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Flyware Bracket System
Y orkville FH2
C12/C15 Flying Hardware
The FH2 hardware kit has been specifically designed to expand the C12 and C15's
already advanced mounting capabilities. A single FH2 installation kit is the ideal rigging
solution for installing Yorkville Sound Coliseum Series C12 or C15 speakers. This kit has
been built for hanging solo cabinets or two-enclosure arrays.
The staggered hole pattern on the FH2 allows for a multitude of tilt angles simply by
moving the shackle towards front or the rear of the bracket. If a greater down-tilt angle is
required, simply add an eye-bolt to the pullback point located on the rear of the cabinet.
When using C12 or C15 cabinets in two cabinet arrays, the FH2 splays the loudspeakers
at the ideal angles to minimize interference and acoustic lobing.
IMPORTANT!! The rigging of loudspeaker systems is an extremely serious matter!
Overhead rigging requires extensive experience, including (but not limited to) calculating
working load limits, hardware installation, and periodic safety inspection of all hardware
and cabinetry. If you lack these qualifications, do not attempt the installation yourself,
but instead use a professional structural rigger. Improper installation can result in bodily
injury or death. Consult a structural engineer to calculate added loads upon the building.
Structural reinforcement may be necessary to insure a safe installation.
Flying Arrays
A single FH2 kit can be used to attach
two cabinets together in a horizontal array
increasing dispersion and helping the cabi-
nets cover a wider area.
Mounting the FH2 Bracket
on Individual Enclosure
The FH2 bracket has been designed to allow
either individual or multiple enclosures to be
flown. In order to fly an individual enclosure,
follow these simple instructions.
Kit Includes
1 FH2W (white) or FH2B (black) Bracket
1 Z1389 Support Plate
1 Z1390 Support Plate
8 YS#8974 1/4-20 X 1 1/4 HEX HEAD BOLT
8 YS#8489 1/4-20 SPLIT WASHER BLACK OXIDE
FH2W(white) or FH2B (black)
Z1389W or Z1389B
Z1390W or Z1390B
Canada
Voice: (905) 837-8481
Fax: (905) 837-8746
w w w . y o r k v i l l e . c o m
Yorkville Sound
550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA
1
YS#8974 x8
YS#8489 x8
U.S.A.
Voice: (716) 297-2920
Fax: (716) 297-3689
Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA
Publicité
Manuels Connexes pour YORKVILLE FH2
Sommaire des Matières pour YORKVILLE FH2
- Page 1 The staggered hole pattern on the FH2 allows for a multitude of tilt angles simply by moving the shackle towards front or the rear of the bracket. If a greater down-tilt angle is required, simply add an eye-bolt to the pullback point located on the rear of the cabinet.
- Page 2 Remove the four flyware bolts on top of the enclosure to be flown. Step 2 - Attaching the Bracket Secure the FH2 bracket to the top of the enclosure using the four supplied washers and bolts. Tighten the bolts in an alternating diagonal pattern. Tighten each bolt gradu- ally, following the diagonal pattern until all are firmly secured.
- Page 3 Step 3 - Support Plate After the FH2 bracket has been successfully installed on the top, lay the enclosures on their back to have access to the bottom. Mount the supplied support plates reusing the bolts just removed, this will secure the enclosures together.
- Page 4 Le kit de quincaillerie de suspension FH2 a été spécialement conçu pour ajouter aux capacités de montage déjà avancé des C12 et C15. Un seul kit d’installation FH2 s’avère la solution idéale pour la suspension des enceintes de la série Yorkville Sound Coliseum C12 ou C15.
- Page 5 être suspendue. Étape 2 - Fixation du Support Fixez le support FH2 sur le dessus de l'enceinte à l'aide des quatre boulons et ron- delles fournies. Serrer les boulons en alternance en diagonale. Serrer chaque boulon progressivement, suivant la diagonale jusqu'à ce que tous soient fermement arrimés.
- Page 6 LokTM). Cela aidera à garder le boulon verrouillé en place. Étape 3 - Plaque De Soutien Une fois le support de FH2 installé avec succès sur le dessus, couchez les enceintes sur leur dos pour avoir accès au dessous. Montez les plaques de support fournis en réutili- sant les boulons que venez de retirer pour fixer solidement les enceintes ensemble.