Disposal And Recycling - Dexter DX50V Traduction Des Instructions D'origine

m Important!
Always depressurize the equipment before carry­
ing out any cleaning and maintenance work! Risk of
injury!
10.1 Cleaning
• Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
• We recommend that you clean the equipment
immediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plas­
tic parts in the equipment. Ensure that no water
can get into the interior of the equipment.
• You must disconnect the hose and any spraying
tools from the compressor before cleaning. Do
not clean the compressor with water, solvents or
the like.
10.2 Maintenance work on the pressure vessel
(fig. 1, 3)
m Important! To ensure a long service life of the
pressure vessel (2), drain off the condensed water
by opening the drain valve (1) each time after using.
Release the vessel pressure first (see 10.3.1). Open
the drain screw by turning counter­clockwise (looking
at the screw from the bottom of the compressor) so
that all the condensed water can run out of the pres­
sure vessel. Then close the drain screw again (turn
it clockwise). Check the pressure vessel for signs of
rust and damage each time before using. Do not use
the compressor with a damaged or rusty pressure
vessel. If you discover any damage, then please con­
tact the customer service workshop.
10.3 Storage
m Important!
Pull out the mains plug and ventilate the equip-
ment and all connected pneumatic tools. Switch
off the compressor and make sure that it is
secured in such a way that it cannot be started
up again by any unauthorized person.
m Important!
Store the compressor only in a dry location
which is not accessible to unauthorized per-
sons. Always store upright, never tilted!
10.3.1 Releasing excess pressure
Release the excess pressure by switching off the
compressor and using the compressed air which
is still left in the pressure vessel, e.g. with a com­
pressed air tool running in idle mode or with a blow­
out pistol.
10.3.2 Safety valve (Fig. 1)
The safety valve (11) has been set for the highest per­
mitted pressure of the pressure vessel. It is not permit­
ted to adjust the safety valve or remove the connec­
tion lock (11.2) between the exhaust nut (11.1) and its
cap (11.3).
Actuate the safety valve every 30 operating hours but
at least 3 times a year, to ensure that it works when
required. Turn the perforated exhaust nut (11.1) coun­
terclockwise to open it and use your hands to pull the
valve rod outwards over the perforated exhaust nut
(11.1) to open the safety valve outlet.
Now, the valve audibly releases air. Then, tighten the
exhaust nut clockwise again.
10.4 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be re­
placed by anyone but a qualified electrician.
10.5 Transport (fig. 1)
The compressor can be transported by tilting to the
wheels.
10.6 Ordering replacement parts
Please quote the following data when ordering
replacement parts:
• Type of machine
• Article number of the machine
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use as
consumables.
Wear parts*: Belt, clutch
* Not necessarily included in the scope of delivery!

11. Disposal and recycling

The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be re­
turned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local
council.
GB | 23