Aurora ShredSafe AU1014XA Mode D'emploi page 3

OPERATION Continued:
I
Auto: This setting allows the shredder to be automatically started by inserting paper into the
shred opening. Always feed the paper in as straight as possible. When the paper has
passed through, the shredder will automatically stop. (FIGURE 2)
O
Off: This setting turns off all features of the shredder. For safety reasons, we recommend that
you leave the shredder in the "Off" position whenever the shredder is unattended or
not in use. (FIGURE 2)
R
Rev: In the unlikely event of a paper jam, the reverse setting can be used to help clear the
cutters of paper that has not passed through. Never attempt to clear a jam by using
the reverse function until you have emptied the wastebasket. (FIGURE 2)
Never shred plastic (except credit cards and CD/DVDs), any hard materials, continuous
forms, newsprint, or anything with adhesives including labels and envelopes.
While this shredder will shred staples, it is recommended that you remove them whenever possible in
order to extend the life of your shredder.
Only shred credit cards by feeding them vertically within the designated area.
Never feed more than one credit card at a time.
Features a CD/DVD destroyer:
1) Hold the CD/DVD by the edge and feed one at a time,
releasing when shredding begins.
2) Shredder will stop when the entire disc has been destroyed.
CAUTION:
Do not hold CD/DVD with finger through the center ring while
feeding into the shredder. Serious injury may occur.
Never feed more than one credit card or CD/DVD at a time.
LED Status indicators:
Power On
(green light) Overload/Overheat
3
Paper Shredder Misaligned
(red light)
(red light)
WARNING :
!
Avoid touching the document
feed opening with hands.
Product is not intended for use by
children (product is not a toy).
Do not insert foreign objects into
the document feed opening.
- RISK OF FIRE. Never use any petroleum based or flammable oils or lubricants in or around the
machine as some oils can combust causing serious injury.
- NEVER dispose of flammable chemicals or materials that have come into contact
with flammable chemicals (for example, nail polish, acetone, gasoline) in the shredder basket.
- Never shred plastic (except credit cards and CD/DVDs), any hard materials, continuous
forms, newsprint, or anything with adhesives including labels and envelopes.
- Do not hold CD/DVD with finger through the center ring while feeding into the
shredder. Serious injury may occur.
- A socket-outlet should be near the equipment and be easily accessible.
- Always turn the shredder off and unplug the power cord from the AC outlet before cleaning it,
moving it, or emptying the waste basket.
- Never let the wastebasket become full. This will lead to shredded material being pulled back up into
the shredder and cause jams.
- Never place the shredder near water or any heat source.
- Keep wastebasket emptied so that the shredder output is not impeded.
- Do not use the shredder if the power cord is damaged in any way.
- Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades
and/or electricity and will void the manufacturers warranty.
- Never try to clean or clear the shredder blade.
TROUBLESHOOTING FOR AURORA PAPER SHREDDERS :
The shredder does not work at all.
a) Make sure the unit is plugged in and that the outlet it is plugged into is in good working order.
b) Be sure to not tilt open the cover completely beyond the preset position, otherwise the
ShredSafe™ power cut off feature will be activated and the shredder will be inoperable.
c) In the event that the shredder is run continuously for too long and the motor overheats, a thermal
overload switch will automatically shut the power off. If this happens, move the switch to the off
position for 30 minutes or more before continuing.
Do not spray or keep any aerosol
products in or around shredder.
Avoid loose clothing or jewelry
touching the document feed opening.
Avoid getting hair near the
document feed opening.
4
Continued on next page