Monacor PA-1200C Mode D'emploi page 14

A Setting of the starting time
1) The display shows:
SET TIME
00:00
The hours can be set with the buttons UP and
DOWN. With the button kept pressed, the hours
advance or reverse.
2) Confirm the setting with the button ENTER. The dis-
play changes to:
SET TIME
xx:00
3) Repeat the procedure for the minutes.
4) After pressing the button ENTER, the display shows:
TIME=xx:xx
<PRESS ENTER>
Press the button ENTER again to confirm the start-
ing time. The submenu for the chime setting
appears.
B Selecting the chime
1) After setting the starting time the display shows:
SET CHIME
CHIME A
2) Either confirm the one-sound chime A with the but-
ton ENTER or select another chime with the button
UP or DOWN.
3) If no chime is to sound at the programmed starting
time, select the menu item NONE CHIME with the
button DOWN.
4) Define the setting with the button ENTER. The dis-
play changes to:
CHIME=x
<PRESS ENTER>
Press the button ENTER again to confirm the chime
setting. The submenu for the selection of the week-
days appears.
C Selecting the weekday(s)
1) After the chime selection the display shows:
SET DAY
1
2) Select the weekday with the button UP or DOWN.
"1" = Monday, "7" = Sunday.
3) With the button ENTER confirm the weekday. The
selected day is marked by an asterisk, e. g.:
SET DAY
3
4) If a wrong weekday was selected, press again the
button ENTER to cancel it.
5) Several days in any desired combination can be
programmed, e. g.
SET DAY
6
6) After all days have been selected, select the menu
item EXIT with the button UP or DOWN (is be -
tween "7" and "1"). Press the button ENTER. The
display shows:
14
[HOUR]
[MINUTE]
R 1234567
R
R 1234567
R *
R 1234567
R ** **
SET DAY=xx
<PRESS ENTER>
Press the button ENTER again to confirm the days.
The submenu for the relay selection appears.
D Selecting the relay
1) After the selection of the weekday the display
shows:
SET REL R 123
1 R
2) With the button UP or DOWN select the relay which
is to pick up at the selected starting time.
3) Confirm the relay with the button ENTER. The se -
lected relay is marked by an asterisk, e. g.:
SET REL R 123
3 R *
4) If a wrong relay was selected, press again the but-
ton ENTER to cancel it.
5) No relay at all or relays in any desired combination
can be programmed, e. g.
SET REL R 123
3 R * *
6) After all relays have been selected, select the menu
item EXIT with the button UP or DOWN. Press the
button ENTER. The display shows:
SET REL=xx
<PRESS ENTER>
Press the button ENTER again to confirm the set-
ting. The submenu for the time delay of the relay
appears.
E Time delay of the relay
If no relay was selected, this menu item is skipped.
The selected relays can pick up at the same time as
the chime or only after the chime has faded away.
1) After the relay selection the display shows:
SET REL DELAY
ON
2) Either activate the time delay with the button UP
(display ON; the relay picks up after the chime) or
deactivate with the button DOWN (display OFF;
the relay picks up at the same time as the chime).
3) Define the setting with the button ENTER. Then the
display shows:
REL DELAY=ON
<PRESS ENTER>
To confirm, press the button ENTER again. The
submenu for the relay status appears.
F Relay status
After selecting the relay time delay, the display shows:
SET REL STATUS
ON
For the selected relays, the following options are avail-
able:
1. In the position ON, the selected relays remain
picked up until a programme step is made with the
option OFF or a hold time is set for the respective
REL DELAY=OFF
or
<PRESS ENTER>