Yamaha MG82cx Mode D'emploi page 16

Reference
Specifications
■ Electrical Specifications
Frequency Response
Total Harmonic Distortion
(THD + N)
Hum & Noise
Hum & Noise are measured
with a 6 dB/octave filter
@12.7 kHz; equivalent to a
20 kHz filter with infinite
dB/octave attenuation.
Crosstalk (1 kHz)
Maximum Voltage Gain (1 kHz)
All level controls are maxi-
mum when measured
PAN/BAL: panned hard left
or hard right.
Phantom Voltage
■ General Specifications
Input HPF
Input Equalization
Turn over/roll-off frequency
of shelving: 3 dB below
maximum variable level.
±15 dB maximum
PEAK Indicator
Internal Digital Effect*
LED Level Meter
Power Supply Adaptor
Power Consumption
Dimensions (W x H x D)
Net Weight
All level controls are nominal if not specified.
Output impedance of signal generator: 150 ohms
* The MG82CX feature is described first, followed by the MG102C feature in brackets: MG82CX (MG102C)
STEREO OUT GAIN: min (CHs 1-5/6)
20 Hz-20 kHz
EFFECT SEND
Nominal output level @1 kHz
(AUX SEND*)
MONITOR OUT, REC OUT
STEREO OUT +14 dBu, 20 Hz-20 kHz, Input Gain Control at mini-
mum
Input: CH INPUT 1, 2 MIC EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN:
maximum (CH1, 2)
STEREO OUT STEREO Master control at nominal level and all
CH Level control at minimum.
EFFECT SEND All CH EFFECT (AUX*) controls at minimum.
(AUX SEND*)
STEREO OUT STEREO Master control and one CH level control
at nominal level (CH1, 2)
STEREO OUT Residual Output Noise
Adjacent Input CH1, 2
Input to Output STEREO L/R, CH 1, 2, PAN: panned hard left or right
Rs = 150 Ω
MIC to CH INSERT OUT
INPUT GAIN: maximum
MIC to STEREO OUT
MIC to REC OUT
MIC to MONITOR OUT
MIC to PHONES OUT
MIC to EFFECT SEND (AUX SEND*)
LINE to STEREO OUT
LINE to EFFECT SEND (AUX SEND*)
ST CH 7/8, (CHs 7/8, 9/10*) to STEREO OUT
Rs = 150 Ω RETURN to STEREO OUT
Rs = 600 Ω 2TR IN to STEREO OUT
MIC no load
CHs 1-5/6, 80 Hz, 12 dB/oct
CHs 1-5/6 HIGH: 10 kHz (shelving)
MID: 2.5 kHz (peaking)
LOW: 100 Hz (shelving)
CH 7/8 (CHs 7/8, 9/10*) HIGH: 10 kHz (shelving)
LOW: 100 Hz (shelving)
Red LED turns on when post EQ signal (either post MIC HA or post EQ signal
for CHs 3/4, 5/6) reaches –3 dB below clipping (+17 dBu).
16 PROGRAM, PARAMETER control
Foot Switch (Digital Effect On/Off)
Pre MONITOR Level 2x7 points LED meter (PEAK, +6, +3, 0, –5, –10, –20 dB)
PEAK lights if the signal level reaches 3 dB below the clipping level.
PA-10 AC 38 VCT, 0.62 A, Cable Length = 3.6 m
21 W
256.6 mm x 62.2 mm x 302.5 mm
1.6 kg (MG82CX), 1.5 kg (MG102C)
MIN TYP MAX
–3.0 1.0
–3.0 1.0
–3.0 1.0
0.1
–128
–87
–85
–64
–100
–70
–70
60
76
58.2
92
81
76
50
47
26
12
23.8
48
MG82CX/MG102C Owner's Manual
UNIT
dB
%
dBu
dB
dB
V
55