General; Fuel/Oil Handling; Fuel; Engine Oil - Husqvarna PP518 Manuel D'utilisation

General

WARNING! Take the following steps to
!
reduce the risk of personal injury and
damage to property.
Take care when handling fuel. Bear in mind
the risk of fire, explosion and inhaling
fumes.
Do not fill with fuel in the vicinity of sparks
or naked flames. Do not smoke.
Only store fuel in containers approved for
the purpose.
Never remove the fuel cap or fill the fuel tank
with fuel while the engine is running. Always
stop the engine and let it cool for a few
minutes before refuelling.
Never fill the fuel tank indoors.
Store and transport the machine and fuel so
that there is no risk of any leakage or fumes
coming into contact with sparks or open
flames, for example, from electrical
machinery, electric motors, electrical relays/
switches or boilers.
Never fill containers inside a vehicle. Always
place the container on the ground away from
your vehicle when filling.
Remove the machine from the vehicle and
refuel it on the ground. If this is not possible,
refuel the equipment with a portable
container, rather than from a petrol
dispenser nozzle.
WARNING! Let the nozzle touch the edge of
!
the fuel tank or the container's opening until
refuelling is completed. Do not use a nozzle
that can be locked in an open position.
If you spill fuel or engine oil on yourself or
your clothes. Change your clothes.
Avoid overfilling. If you have spilled fuel or
engine oil on the machine. Wipe off the spill
and allow the remaining fuel to evaporate.
Tighten the fuel cap carefully after refuelling.
CAUTION! Handle oil, oil filters, fuel and the battery
carefully, of environmental considerations. Follow the local
recycling requirements.
8 –
English

FUEL/OIL HANDLING

Fuel

The Briggs & Stratton engine is guaranteed to run on
unleaded petrol with an octane rating of 86 or more as defined
by the 'Pump Octane Number' (M+R) or 91 or more as defined
by the 'Research Octane Number' (RON). Refuel in a well
ventilated area with the engine turned off.
Unleaded standard petrol not containing more than 10%
ethanol (E10) can be used. Do not use petrol that contains
methanol.
If fuel with an ethanol content higher than 10% (E10) is used,
there may be problems starting and/or operating the unit. It
may also damage metal, rubber and plastic components in
the fuel system, and can be a fire hazard.
Do not use fuel that is older than 30 days. Old fuel can cause
running problems as well as fuel system damage.
The engine will not operate with fuel that is sold as E85
(85% ethanol).

Engine oil

Recommended oil

The engine holds approximately 1.4 l (1-1/2 qt/48 oz) of oil,
when both the oil and oil filter are replaced.
•
•
•
•
Using a synthetic oil does not alter the required oil change
intervals. See the accompanying instruction manual from
Briggs & Stratton for complete details on the oil.

Hydraulic oil

All high quality hydraulic oils with a viscosity index of ISO 46
(46 cSt) can be used.
High quality hydraulic oils which are marketed as
"biodegradable" can be used with a viscosity index similar to
ISO 46.
Consult and comply with the supplier's recommendations with
regard to the oil's service life.
The hydraulic system can also be used with some "food
quality" oils, and can be used in certain applications. Contact
Husqvarna Construction Products for assistance.
Use a high quality detergent oil classified "For Service SF,
SG, SH, SJ" or higher.
Briggs & Stratton strongly recommends that synthetic oils
are used.
Do not use any specific oil additives.
Select viscosity according to the table below.
SAE VISCOSITY GRADES
5W-30
SYNTHETIC OIL 5W-30, 10W-30
-20 0 30
F
C -30 -20 -10
TEMPERATURE RANGE ANTICIPATE D BEFORE NEXT OIL CHANGE
CAUTION! Biodegradable hydraulic oils may require other
service intervals compared to the traditional mineral-based
oils.
SAE 30
32 40 100
60 80
0 10 20 30 40