Important Safety Instructions; Instructions Pertaining To Arisk Of Fire, Electric Shock, Or Injury To Persons; Tool Components And Specifications; Work Area - Campbell Hausfeld NB006750 Mode D'emploi

Operating Instructions

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A
RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS
This manual contains safety, operational
and maintenance information. Contact
your Campbell Hausfeld representative
if you have any questions.
When using tools,
basic precautions
should always be followed, including the
following:
CALIFORNIA PROPOSITION 65
This product or
its power cord may
contain chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm. Wash hands after
handling.
You can create dust when you
cut, sand, drill or grind materials
such as wood, paint, metal,
concrete, cement, or other masonry. This dust
often contains chemicals known to cause
cancer, birth defects, or other reproductive
harm. Wear protective gear.
GENERAL
a. To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.

Tool Components and Specifications

• REQUIRES: 0.7 SCFM with 10 nails per minute
@ 90 psi
• AIR INLET: 1/4 inch NPT
• NAIL SIZE RANGE: 1 inch to 2-1/2 inch
• MAGAZINE CAPACITY: 100 Nails per load, 16
gauge
• WEIGHT: 4 lbs., 13 oz.
• LENGTH: 12-1/2 inch
• HEIGHT: 11-1/2 inch
• MAXIMUM PRESSURE: 110 psi
• PRESSURE RANGE: 70 - 110 psi
www.chpower.com
b. Be thoroughly familiar with the
controls and the proper use of the
equipment. Follow all instructions.
Contact your Campbell Hausfeld
representative if you have any
questions.
c. Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit.
Read and understand
tool labels and
manual. Failure to follow warnings, dangers,
and cautions could result in DEATH or
SERIOUS INJURY.

WORK AREA

a. Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
b. Do not operate the tool
in explosive atmospheres,
such as in the presence of
flammable liquids, gases,
or dust. The tool is able to create
sparks resulting in the ignition of
the dust or fumes.
c. Keep bystanders, children, and
visitors away while operating the
tool. Distractions are able to result in
the loss of control of the tool.
Quick
Clear
Latch
No-Mar Tip
2

PERSONAL SAFETY

a. Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons.
b. Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts.
c. Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on
the switch or connect the tool to the
air supply with the switch on.
d. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables
better control of the tool in
unexpected situations.
e. Use safety equipment. A dust mask,
non-skid safety shoes and a hard
hat must be used for the applicable
conditions.
Adjustable Exhaust
Trigger
Depth
Adjustment
Wheel
Work Contact
Element (WCE)
Magazine Latch
Magazine (open)
Name, Spec and
Warning Label
(back-side and top)