Important Safety Instructions; Tool Components And Specifications - Campbell Hausfeld SB514000 Mode D'emploi

Operating Instructions

Important Safety Instructions

INSTRUCTIONS PERTaINING TO a
RISK OF FIRE, ElECTRIC ShOCK, OR
INJURY TO PERSONS
This manual contains safety, operational
and maintenance information. Contact
your Campbell Hausfeld representative
if you have any questions.
When using tools,
basic precautions
should always be followed,
including the following:
CalIFORNIa PROPOSITION 65
This product or
its power cord
may contain chemicals known to
the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
after handling.
You can create dust
when you cut, sand, drill
or grind materials such
as wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
GENERal
a. To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.

Tool Components and Specifications

• REqUIRES: 0.4 SCFM with 10 fasteners
per minute @ 90 psi
• aIR INlET: 1/4 inch NPT
• MaGaZINE CaPaCITY: 100 fasteners
per load, 18 gauge
• BRaDS: 3/8 inch to 2 inch
• STaPlES: 1/2 inch to 1-1/2 inch; 1/4 inch
crown
• WEIGhT: 3 lbs., 9 oz.
• lENGTh: 10-1/4 inch
• hEIGhT: 10-1/4 inch
• MaXIMUM PRESSURE: 120 psi
• PRESSURE RaNGE: 60 - 120 psi
www.chpower.com
b. Be thoroughly familiar with the
controls and the proper use of the
equipment. Follow all instructions.
Contact your Campbell Hausfeld
representative if you have any
questions.
c. Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit.
Read and
understand tool
labels and manual. Failure to follow
warnings, dangers, and cautions
could result in DEATH or SERIOUS
INJURY.
WORK aREa
a. Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
b. Do not operate the tool
in explosive atmospheres,
such as in the presence
of flammable liquids,
gases, or dust. The tool is
able to create sparks resulting in the
ignition of the dust or fumes.
c. Keep bystanders, children, and
visitors away while operating the
tool. Distractions are able to result in
the loss of control of the tool.
PERSONal SaFETY
a. Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
Quick Clear Nose
Work Contact
Element (WCE)
2
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons.
b. Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts.
c. Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on
the switch or connect the tool to the
air supply with the switch on.
d. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables
better control of the tool in
unexpected situations.
e. Use safety equipment. A dust mask,
non-skid safety shoes and a hard
hat must be used for the applicable
conditions.
f. Always wear eye
protection.
Cap Exhaust
Trigger
Fastener Discharge Area
Warning
Label
Latch
Button
Magazine