Technical Data; Eu Declaration Of Conformity - Chicago Pneumatic CP7748 Manuel De L'opérateur

Impact Wrenches

Technical data

Min. working torque forward
(ft.lb)
Max. working torque forward
(ft.lb)
Min. working torque (Nm)
Max. working torque (Nm)
Max. torque (reverse) (ft.lb)
Max. torque (reverse) (Nm)
Free speed (rpm)
Weight (lb)
Weight (kg)
Declarations

EU DECLARATION OF CONFORMITY

We, CHICAGO PNEUMATIC Tool Co. LLC, 1815 Club-
house Road, Rock Hill, SC 29730, declare under our sole re-
sponsibility that the product (with name, type and serial
number, see front page) is in conformity with the following
Directive(s):
2006/42/EC (17/05/2006)
Harmonized standards applied:
EN ISO 11148-6:2012
Authorities can request relevant technical information from:
Pascal Roussy, R&D Manager, Ets Georges Renault, 38 rue
Bobby Sands, BP10273 44818 Saint Herblain, France
Saint-Herblain,
Pascal ROUSSY
Signature of issuer
Noise and vibration
Sound pressure level (dB(A))
Vibration uncertainty
Vibration (m/s²)
Uncertainty 3 dB(A), in accordance with ISO 15744. For
Sound power level, add 11 dB(A)
Vibration standard : ISO 28927-2
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
CP7748 CP7748-2
70 70
555 555
95 95
750 750
960 960
1300 1300
7000 7000
4.4 4.65
2 2.11
CP7748 CP7748-2
94.3 94.3
4.5 3.8
12 11.3
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, CHICAGO PNEUMATIC Tool Co. LLC, cannot be
held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
rop.eu/index.php and selecting 'Tools' then 'Legislation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
Product specific instructions
Operation
See figures on page 2.
• Fix the accessories properly to the tool.
• Connect device to a clean and dry air supply.
• To start the machine, use the trigger (A). Machine speed
is increase by increasing pressure on the trigger. Release
the trigger to stop.
• To switch rotation, use the switch (B / C). Use the re-
verse switch (B / C) only when the drive spindle comes
to a complete stop. Changing the speed before the drive
spindle stops may damage the machine.
• To adjust output power, use the regulator (B / C).
Clutch lubrication
Use 0.14 oz. (4 g) of CP Pneu-Lube Synthetic Clutch grease.
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
(2) drops per minute. If an air line lubricator cannot be used,
add air motor oil to the inlet once a day.
Maintenance instructions
• Follow local country environmental regulations for
safe handling and disposal of all components.
http://www.pneu-
5