Kettler CTR 1 Mode D'emploi Et Instructions D'entraînement page 3

GB
Assembly Instructions
Before assembling or using the exercise cycle , please read the following instructions carefully. They contain important
information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a
safe place for maintenance purposes or for ordering spare parts.
For Your Safety
The crosstrainer should be used only for its intended purpose,
i.e. for physical exercise by adult persons.
Any other use of the equipment is prohibited and may be dan-
gerous. The manufacturer cannot be held liable for damage or
injury caused by improper use of the equipment.
The crosstrainer has been designed in accordance with the latest
standards of safety. Any features which may have been a possible
cause of injury have been avoided or made as safe as possible.
Incorrect repairs and structural modifications (e.g. removal or re-
placement of original parts) may endanger the safety of the user.
Damaged components may endanger your safety or reduce the
lifetime of the equipment. For this reason, worn or damaged parts
should be replaced immediately and the equipment taken out of
use until this has been done. Use only original KETTLER spare parts.
If the equipment is in regular use, check all its components thor-
oughly every 1 -2 months. Pay particular attention to the tight-
ness of bolts and nuts. This is particularly true for the attach-
Handling the equipment
Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave un-
predictably and dangerous situations may occur for which the
manufacturer cannot be held liable. If, in spite of this, children
are allowed to use the equipment, ensure that they are in-
structed in its proper use and supervised accordingly.
The crosstrainer complies with the DIN EN 957 - 1/9, class
HA. It is therefore suitable for therapeutic use.
A slight production of noise at the bearing of the centrifugal
mass is due to the construction and has no negative effect
Instructions for Assembly
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
The equipment must be assembled with due care by an adult per-
son. If in doubt call upon the help of a second person, if possible
technically talented.
Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
Ensure that your working area is free of possible sources of danger,
for example don't leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
List of spare parts
When ordering spare parts, always state the full article number, spare-part num-
ber, the quantity required and the inspection number stamped on the back.
Example order: Art. no. 07858-600 / spare-part no. 67000170/ 2
pieces / inspection no......
Important: spare part prices do not include fastening material; if fastening
material (bolts, nuts, washers etc.) is required, this should be clearly stated
on the order by adding the words „with fastening material".
ment of grip strap, running plate and fastening of the handle-
bar and front tube.
To ensure that the safety level is kept to the highest possible
standard, determined by its construction, this product should
be serviced regulary (once a year) by specialist retailers.
Instruct persons using the equipment (in particular children) on
possible sources of danger during exercising.
Before beginning your program of exercise, consult your doctor
to ensure that you are fit enough to use the equipment. Base your
program of exercise on the advice given by your doctor. Incor-
rect or excessive exercise may damage your health!
Any interference with parts of the product that are not described wit-
hin the manual may cause damage, or endanger the person using this
machine. Extensive repairs must only be carried out by KETTLER servi-
ce staff or qualified personnel trained by KETTLER.
In case of enquiry, please contact your KETTLER dealer.
upon operation. Possibly occurring noise during reverse pe-
dalling result from engineering and are absolutely safe.
Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment.
The crosstrainer has a magnetic brake system.
The equipment is independent of revolutions per minute.
Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.
Before use, always check all screws and plug-in connections
as well as respective safety devices fit correctly.
Always wear suitable shoes when using.
All electric appliances emit electromagnetic radiation when in oper-
ation. Please do not leave especially radiation-intensive appliances
(e.g. mobile telephones) directly next to the cockpit or the electronic
controlsystem as otherwise values displayed might be distorted (e.g.
pulse measurement
is always a risk of suffocation if children play with plastic bags!
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
structed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until re-
sistance is felt, then use spanner to finally tighten nuts completely
against resistance (locking device). Then check that all screw con-
nections have been tightened firmly. Attention: once locknuts have
been unscrewed they no longer function correctly (the locking de-
vice is destroyed), and must be replaced.
For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach · VA
23450 USA
http://www.kettler.net
3