Wheel Nut; Wheel Guard Screw M6 X 1-6G 14 Mm Long; 638 10-32 X 1/2" Long (2); Wheel Guard Screw Lock Washer (2) (For Use With 77H-638) - Ingersoll Rand 77H Serie Manuel D'exploitation Et D'entretien

PART NUMBER FOR ORDERING
+ 24 Controller Assembly (consists of
Controller and Rear End Plate Assembly)
for 77H90G6, 77H90H84,
77H90L10 and 77H30B106
for 77H120H84, 77H120H63 and
77H120110 . . . . . . . . . . . . . . . . . . .
for 77H50B106 . . . . . . . . . . . . . . . .
25 Rear End Plate Assembly (consists of rear
end plate, rotor bearing and required
spacers) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 Rear End Plate Gasket . . . . . . . . . . . . . . . . . . .
27 Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
+ 28 Rotor
for 77H30B106 and
77H50B106 (9 teeth) . . . . . . . . . . .
for all others (13 teeth) . . . . . . . . . .
29 Vane Packet (set of 4 Vanes) . . . . . . . . . . . . . .
30 Front End Plate . . . . . . . . . . . . . . . . . . . . . . . .
31 Front Rotor Bearing . . . . . . . . . . . . . . . . . . . . .
32 Cylinder Dowel . . . . . . . . . . . . . . . . . . . . . . . .
33 Motor Spacer . . . . . . . . . . . . . . . . . . . . . . . . . .
34 Arbor Coupling . . . . . . . . . . . . . . . . . . . . . . . .
* Controller Wrench . . . . . . . . . . . . . . . . . . . . . .
* Valve Seat Support Retaining Pliers . . . . . . . .
* Coupling Nut Wrench . . . . . . . . . . . . . . . . . . .
* Vibra–TiteR** (0.6 cc) (2) . . . . . . . . . . . . . . .
* Adhesive Kit . . . . . . . . . . . . . . . . . . . . . . . . . .
* Tune–up Kit (includes illustrated parts 3 [2],
5, 6, 12, 13 [2], 26 and 29) . . . . . . . . . . . . . . .
* Not illustrated.
+ Early models of these Grinders had Rotors and Controller Assemblies with left–hand threads. If you have a model with a left–hand thread, contact
Ingersoll–Rand when ordering replacement parts.
** Registered trademark of ND Industries.

THE FOLLOWING PARTS ARE USED

IN MODELS 77H90H84, 77H90H84–EU,
77H120H84 AND 77H120H84–EU
77H90–A524ARH TYPE 1 RADIAL WHEEL GRINDERS
35 Arbor (13 teeth) . . . . . . . . . . . . . . . . . . . . . . . .
77H120–A524ARH 36B Dust Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77H150–A524ARH 40 Bearing Locknut . . . . . . . . . . . . . . . . . . . . . . .
41 Bearing Lock Washer . . . . . . . . . . . . . . . . . . .
42 Wheel End Bearing . . . . . . . . . . . . . . . . . . . . .
77H–A12 43 Wheel Guard (4" x 1") . . . . . . . . . . . . . . . . . .
77H–739 44 Wheel Flange (2) . . . . . . . . . . . . . . . . . . . . . . .
77H–3 46

Wheel Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . .

47 Wheel Guard Screw
77H30–53RH
77H–53ARH 48 Wheel Guard Lock Washer (2) (for use with
77H–42–4 No. 77H–638) . . . . . . . . . . . . . . . . . . . . . . . . .
77H–11 THE FOLLOWING PARTS ARE USED
77H–24
77H120H63–EU TYPE 1 RADIAL
77H–98
77E–208–H8
77E–304A 36 Arbor (13 teeth) . . . . . . . . . . . . . . . . . . . . . . . .
77H–950 36A Wheel Flange Pin . . . . . . . . . . . . . . . . . . . .
77H–154 36B Dust Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77H–281 49 Bearing Locknut . . . . . . . . . . . . . . . . . . . . . . .
5R–VT06 50 Bearing Lock Washer . . . . . . . . . . . . . . . . . . .
77H–KVLT 51 Wheel End Bearing . . . . . . . . . . . . . . . . . . . . .
52 Wheel Guard (3" x 1/2") . . . . . . . . . . . . . . . . .
77H/77A–TK3 53 Wheel Flange (2) . . . . . . . . . . . . . . . . . . . . . . .
PART NUMBER FOR ORDERING
M6 x 1–6g 14 mm long (2) . . . . . . . . .
10–32 x 1/2" long (2) . . . . . . . . . . . . . .
IN MODELS 77H120H63 AND
WHEEL GRINDERS
77E–4A–H8
77H–930
77H–824–H6
77H–66–H6
77H–33–H6
77H–941
77H–16–H8
215–182
77H–638
FEA100–26
88H60–67
77E–A4A–H6
77H–84
77H–930
77H–824–H6
77H–66–H6
77H–33–H6
77H–931
77H–16–H6