Symmons Identity 6706 Manuel D'utilisation Et D'entretien

Symmons Identity 6706 Manuel D'utilisation Et D'entretien

Système de douche/douche à main/baignoire

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

6706
Tub/Shower/Hand Shower System
Operation & Maintenance Manual
Model Numbers
6706
Identity Tub/Shower/Hand Shower System
Specification
Tub/shower/hand shower system powered by the
Temptrol
®
pressure-balancing valve. Features adjustable
stop screw to limit handle turn, separate three function
diverter, non-diverter tub spout, wall ell, in-line vacuum
breaker, 60" flexible metal hose, hand shower cradle,
1 mode hand shower, 1 mode showerhead with easy to
clean rubber nozzles and standard 2.5 gpm (9.5 L/min) flow
restrictors. Components made from metal and nonmetallic
materials, plated in standard polished chrome finish.
Compliance
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5 gpm (5.7 L/min)
For California Residents
WARNING: This product contains chemicals known to the
State of California to cause cancer, birth defects, or other
reproductive harm.
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Identity
Modifications
Certi ed by
CSA Group
Note: Append appropriate -suffix to model number.
-1.5
1.5 gpm (5.7 L/min) flow restrictor
-2.0
2.0 gpm (7.6 L/min) flow restrictor
6' metal hose in place of 5' standard
-72
metal hose
-143
3 mode showerhead
-145
5 mode showerhead
-231
2 mode showerhead
30" slide bar in place of wall cradle
-B30
48" slide bar in place of wall cradle
-B48
-CHKS
Integral check stops - for use in
installations where a positive shut-off
device is used downstream of mixing valve
-IPS
1/2" female IPS connections
Less showerhead
-L/HD
Less hand shower
-L/HS
-LP
Loop handle
-LR
Lever handle
-OP
13" oval plate
Quick disconnect on hand shower units
-QD
White vinyl hose in place of metal hose
-R
Rebuild trim kit
-REB-TRM
-REV
Reverse coring, hot on right, cold on
left, for back to back installations
-SS
Slip spout on any tub/shower/hand
shower unit
-STN
Satin Nickel finish
-T724
24" slide / grab bar with ADA hand
shower in place of standard hand show-
er unit
-T736
36" slide / grab bar with ADA hand
shower in place of standard hand show-
er unit
-TRM
Trim only, valve not included
-X
Integral service stops - allows water
shutoff at valve for service

Publicité

Table des Matières
loading

Sommaire des Matières pour Symmons Identity 6706

  • Page 1 Limited Lifetime - to the original end purchaser in consumer/residential installations.  Slip spout on any tub/shower/hand 5 Years - for industrial/commercial installations. shower unit Refer to www.symmons.com/warranty for complete  -STN Satin Nickel finish warranty information.  -T724 24"...
  • Page 2: Dimensions

    Dimensions Measurements 5-7/8", 149 mm 4-5/8", 117 mm Male 1/2" NPT fitting must be recessed 1/4" (6 mm) from finished wall Diverter Valve Hole Size Min. Ø 3", 76 mm Max. Ø 3-1/4", 83 mm 3-5/8", 92 mm 2-7/8", 73 mm Ref.
  • Page 3: Parts Breakdown

    Parts Breakdown Replacement Parts Item Description Part Number Hand Shower EF-100* Wall Ell EF-105* Set Screw Mounting Plate Wall Cradle EF-106* Screws Vacuum Breaker EF-104* 60" Hose Showerhead 672SH* Shower Arm 300S* Flange Handle RTS-281* Set Screw Dome Cover T-19* Diverter 67-DIV* Escutcheon Kit...
  • Page 4 Installation Note: 4) Install dome covers (N) to valves. 6) Attach shower arm (J) and flange For valve body installation, please Turn clockwise to secure. (K) to vertical shower pipe. Turn see valve body manual. clockwise to tighten. 1) Install shower mounting plate (S) to shower valve.
  • Page 5 Installation 9) Place mounting plate (C) in po- 10) Remove cover of hand show- 11) Attach vacuum breaker (G) to wall sition, mark and drill 3/16" holes er cradle (E). Install cradle and ell (B). Attach hose (H) to vacuum for tile anchors (U1), 5/16"...
  • Page 6: Troubleshooting Chart

    ■ ■ ■ ■ Symmons Industries, Inc. 31 Brooks Drive Braintree, MA 02184 Phone: (800) 796-6667 Fax: (800) 961-9621 ■ ■ ■ ■ Copyright © 2016 Symmons Industries, Inc. symmons.com gethelp@symmons.com ZV-3199 REV 0 052416...
  • Page 7 5 años - para instalaciones industriales y comerciales. Surtidor de montaje deslizante en cualquiera de  Consulte www.symmons.com/warranty para obtener las unidades para bañera/ducha/ducha de mano. información más completa sobre la garantía. -STN Acabado de níquel satinado...
  • Page 8 Dimensiones Medidas 5-7/8", 149 mm 4-5/8", 117 mm La rosca macho NPT de 1/2” debe estar empotrada a 1/4” (6 mm) de la pared terminada Tamaño de los orificios de la válvula de desvío Mín. Ø 3”, 76 mm Máx. Ø 3-1/4", 83 mm 3-5/8", 92 mm 2-7/8", 73 mm Ref.
  • Page 9: Desglose De Piezas

    Desglose de piezas Repuestos Número Artículo Descripción de la pieza Ducha de mano EF-100* Codo de pared EF-105* Tornillo de presión Placa de montaje Soporte de pared EF-106* Tornillos Igualador de presión EF-104* Manguera de 60” Cabezal de ducha 672SH* Brida del brazo de 300S* la ducha...
  • Page 10 Instalación Nota: 4) Instale las cubiertas de domo 6) Una el brazo de la ducha (J) y Para instalar el cuerpo de la válvula, (N) en las válvulas. Gire en el la brida (K) al tubo vertical de la vea el manual de la válvula. sentido de las manecillas del ducha.
  • Page 11 Instalación 9) Coloque la placa de montaje (C) 10) Retire la cubierta del soporte de 11) Una el igualador de presión (G) en su posición, marque y taladre la ducha de mano (E). Instale el al codo de pared (B). Una la agujeros de 3/16"...
  • Page 12: Tabla De Resolución De Problemas

    ■ ■ ■ ■ Symmons Industries, Inc. 31 Brooks Drive Braintree, MA 02184 Teléfono: (800) 796-6667 Fax: (800) 961-9621 ■ ■ ■ ■ Copyright © 2016 Symmons Industries, Inc. symmons.com gethelp@symmons.com ZV-3199 REV 0 052416...
  • Page 13: Spécifications

    Corps central inversé, l'eau chaude à la droite,  5 ans – pour des installations commerciales et l'eau froide à la gauche, pour installations dos industrielles. Se reporter au site www.symmons.com/ à dos warranty pour des informations complètes concernant Bec de baignoire à enfiler sur toute unité de ...
  • Page 14 Dimensions Mesures 5-7/8 po, 149 mm 4-5/8 po, 117 mm Raccord NPT 1/2 po mâle doit être encastré à 1/4 po (6 mm) du mur fini Taille du trou pour la vanne de dérivation Min. Ø 3 po, 76 mm Max. Ø 3-1/4 po, 83 mm 3-5/8 po, 92 mm 2-7/8 po, 73 mm Réf. 10 po, 254 mm Taille du trou pour...
  • Page 15: Liste Des Pièces

    Liste des pièces Pièces de rechange Numéro Article Description de pièce Douche à main EF-100* Coude mural EF-105* Vis de pression Plaque de montage Support mural EF-106* Brise-vide EF-104* Tuyau de 60 po Pomme de douche 672SH* Bras et bride de 300S* douche Assemblage...
  • Page 16 Installation Remarque : Pour l'installation du 4) Installez les couvercles en dôme 6) Attachez le bras de douche (J) et corps de vanne, veuillez consulter le (N) sur les vannes. Tournez dans la bride (K) au tuyau de douche manuel du corps de vanne. le sens des aiguilles d'une montre vertical.
  • Page 17: Fonctionnement (Contrôle De La Température)

    Installation 9) Placez la plaque de montage (C) 10) Enlevez le couvercle du support 11) Fixez le brise-vide (G) au coude en position, marquez et percez de la douche à main (E). Installez mural (B). Attachez le boyau (H) des trous de 3/16 po pour l'an- le support mural et la plaque de au brise-vide.
  • Page 18: Fonctionnement (Contrôle De La Dérivation)

    à l'eau. ■ ■ ■ ■ Symmons Industries, Inc. 31 Brooks Drive Braintree, MA 02184 Téléphone : (800) 796-6667 Télécopieur : (800) 961-9621 ■ ■ ■ ■ Copyright © 2016 Symmons Industries, Inc. www.symmons.com gethelp@symmons.com ZV-3199 REV 0 052416...

Table des Matières