Table des Matières
Publicité
Le déballage de votre assemblage de guide
Lors du déballage de votre assemblage de guide, vérifiez que toutes les composantes se trouvant sur cette
page sont incluses. Portez une attention particulière lorsque vous déballez votre assemblage de guide afin de
prévenir tout dommage aux composantes.
left rear rail
tablette de soutien
material
support shelf
pour matériaux
fence
guide
rail avant
front rail
rail arrière
de gauche
grand crochet
de rangement
owner's manual
large
storage
hook
(deux)
(two)
SawStop
®
Contractor Fence Assembly
OWNER'S MANUAL
guide de
l'utilisateur
poignée
fence
de guide
affiche pour instructions d'installation
handle
SawStop Assemblage du Guide pour Entrepreneur
rail arrière
right rear rail
de droite
small
petit crochet
storage
de rangement
hook
(deux)
(two)
Hardware Pack
3
#
Installing the Fence Rails Assembly
Hardware for Steps 1-11
Square Head Screws, M8 x 20
16
(10 + 1 extra)
Lock Washers, M8
17
(22 + 1 extra)
Hex Nuts, M8
18
(18 + 1 extra)
Hex Screws, M8 x 16
Carriage Bolts,
19
20
(8 + 1 extra)
M8 x 20 (4)
hardware pack #3
emballage de
quincaillerie no 3
Installing Your SawStop Contractor Fence Assembly
®
Installing the Fence Rails
•
Remove eight M8 x 20 square head screws
16
from the
hardware pack and slide the square head of each screw into the
Assembly
slot along the rear edge of the front rail.
• Locate the front rail, the left and right rear rails, and hardware
pack #3. All of the hardware needed to install the rails is located
on hardware pack #3. In order to easily identify the hardware
used in each of the following steps, the different pieces of
hardware are numbered on the hardware pack and in the figures.
If you are missing hardware pack #3 or any of the other fence
assembly components, call the SawStop Service Department at
503-682-6222 for replacements.
Hardware Pack
3
#
You will also need the following tools
Installing the Fence Rails
Hardware for Steps 1-10
16
to complete the fence assembly:
Square Head Screws, M8 x 20
1. two 13 mm wrenches
(10 + 1 extra)
16
• Adjust the position of each square head screw so that all eight
2. a level or straight-edge
screws align with the corresponding mounting holes in the front
Lock Washers, M8
17
3. a rubber hammer or mallet
(22 + 1 extra)
16
edge of the table top and extension wings. Position the front rail
1
2
3
Hex Nuts, M8
against the edge of the table with the eight screws
(18 + 1 extra)
18
extending through their corresponding mounting holes.
Hex Screws, M8 x 16
19
Carriage Bolts,
20
(8 + 1 extra)
M8 x 20 (4)
Make sure the rulers on the front rail are facing up.
19
• Repeat the same procedure to mount the right rear rail (the
17
19
straight-edge
longer rail) to the rear of the table and to the right extension
17
19
wing. Again use three M8 x 16 hex screws
19
, three M8 lock
washers
, and one M8 hex nut
. Hand tighten the hex
17
18
screws; do not fully tighten them. The right rear rail should
extend beyond the right extension wing.
19
19
17
19
17
17
18
• Mount the left rear rail (the shorter rail)
to the rear of the table and to the left extension
17
wing using three M8 x 16 hex screws
19
, three
18
M8 lock washers
, and one M8 hex nut
. Insert one hex
• Use a straight-edge to level the rear edge of the left extension
17
18
screw into the hole in the extension wing and then use a lock
wing to the cast iron table top. You may have to pull up or push
washer and hex nut to hold the screw in place, as shown. The
down on the outer edge of the extension wing to level it. Once the
5
6
7
other two hex screws thread into corresponding holes
rear edge of the left extension wing is level, use 13 mm
in the cast iron table. Place a lock washer on each
wrenches to fully tighten the hardware that mounts the
screw before threading them into the holes. Hand
left rear rail. Repeat this process to level the rear edge
tighten the hex screws; do not fully tighten them.
of the right extension wing and secure the right rear rail.
installation instructions poster
SawStop Service Department
503-682-6222
www.sawstop.com
© SawStop, LLC
• Place an M8 lock washer
17
and thread an M8 hex nut
on
18
the back of each of the eight square head screws, but do not fully
tighten the nuts at this time. Position the front rail so that the left
3
end of the rail extends about ⁄ inch past the edge of the left
4
extension wing.
17
18
4
• Locate the material support shelf, the two large storage hooks,
the two small storage hooks, and hardware pack #3. All of the
hardware needed to assemble the material support shelf is
located on hardware pack #3. Take the material support shelf
and insert two M8 x 20 square head screws
16
into the holes on
one end. Place an M8 lock washer
17
and a M8 hex nut
18
on
the back of each screw, but do not tighten the nuts.
16
Hardware Pack
3
#
Installing the Fence Rails
Hardware for Steps 1-10
17
18
Square Head Screws, M8 x 20
16
(10 + 1 extra)
Lock Washers, M8
(22 + 1 extra)
17
(18 + 1 extra)
Hex Nuts, M8
18
Hex Screws, M8 x 16
(8 + 1 extra)
19
Carriage Bolts,
M8 x 20 (4)
20
8
|
79
Publicité
Chapitres
Table des Matières
