Feed Water Chemistry Requirements; Installation Precautions - Watts OneFlow OF240-4 Manuel D'installation, D'utilisation Et D'entretien

Feed Water Chemistry Requirements

pH
Hardness (maximum)
Water Pressure
Temperature
Free Chlorine
Iron (maximum)
Manganese (maximum)
Copper
Oil & H2S
Total Phosphates
Silica (maximum)
TDS
NOTICE
* Systems using OneFlow
®
ling lime-scale formation inside the plumbing system at influent
hardness levels up to 75 grains per gallon (1282 mg/l) CaCO3
of calcium carbonate. Due to variances in water chemistry, 30
grains per gallon is a recommended hardness maximum due to
potential aesthetic issues related to soft scale residue formation
outside of the plumbing system. Testing should be performed to
determine proper application where hardness levels exceed 30
grains per gallon.
**Just as with conventional water softening media, OneFlow
media needs to be protected from excess levels of certain metals
that can easily coat the active surface, reducing its effectiveness
over time. Public water supplies rarely, if ever, present a problem,
but if the water supply is from a private well, confirm that the
levels of iron (Fe) and manganese (Mn) are less than 0.3 mg/L
and 0.05 mg/L, respectively.
WARNING
!
***Pursuant to the EPA drinking water standards, the copper
concentration permitted is up to 1.3 ppm. Typically originating
from new copper plumbing, high levels of copper can foul
OneFlow media. New Copper lines need to be passivated for
a minumum of 4 weeks before placing unit into service. For
applications with copper concentration greater than 1.3 ppm,
please consult Watts Water Quality Technical Service. To further
minimize any problem with excess copper, avoid applying
excessive flux on the inner surfaces of the pipe and use a
low-corrosivity water soluble flux listed under the ASTM B813
standard.
NOTICE
† OneFlow media does not reduce silica scaling. While silica
®
tends to have a less significant effect on scale formation than
other minerals, it can act as a binder that makes water spots and
scale residue outside the plumbing system difficult to remove.
This 20 ppm limitation is for aesthetic purposes.
†† All other contaminants must meet the requirements of the
USEPA Safe Drinking Water Act. Specific Mineral and Metal
MCL's, identified in Watts published Feed Water Chemistry
Requirements, supersedes the USEPA SDWA.
Water known to have heavy loads of dirt and debris may require
pre-filtration prior to OneFlow
6.5-8.5
30 grains (513 ppm CaCO3)
15 psi to 90 psi (1.03 bar to 6.21 bar)
40° F to 100° F (5°C to 38°C)
<2 ppm
0.3 ppm
0.05 ppm
1.3 ppm*
Must be Removed Prior to OneFlow
< 3.0 ppm
20 ppm**
1500 mg/l****
technology are effective at control-
.
®
WARNING
!

Installation Precautions

• Do NOT install system on line pressure above 90psi.
• Do NOT install system on HOT water line. Failure to limit line
temperature to 100° F/38° C may result in housing failure
and damage.
• Do NOT install the system backwards with the feed water
line connected to the outlet.
• Do NOT use liquid pipe compounds for fitting connections.
USE two to three wraps of Teflon® tape.
• Do NOT solder plumbing connections attached to filter
housing or inlet valve. Inlet valve and filter housing will be
damaged by high temperature.
• Do NOT allow system to freeze. Turn off water supply to
housing and drain housing if temperature falls below 32°F.
• Do NOT install system in direct sunlight or where system is
exposed to harsh chemicals or may be subjected to being
struck by moving equipment, carts, mops or any other
item that may cause damage.
• ALLOW a minimum of 3" under the housing to allow for
filter replacement.
• IF water hammer is evident, install water hammer arrestors
before the OneFlow
• Do NOT overtighten fitting connections into inlet valve or
®
housing outlet.
• Always back-up valves and fittings with a wrench when
installing a fitting to avoid turning the valve.
• Do NOT install the unit behind equipment where it may be dif-
ficult to access the system for filter replacement.
Position the OneFlow
of flow through the OneFlow
this in mind when determining installation location. Do NOT
mount the OneFlow
do not mount the system above any device or area that would
be adversely affected by water.
2
unit.
®
unit in a suitable location. The direction
®
unit is always left to right; keep
®
system near any source of heat. Also,
®