Technical Specifications - Leister CSS EASY Instructions D'utilisation

INSTALLATION
Dimensions and cut-out; panel mounting
63
48
48
99
10
PANEL MOUNTING:
To fix the unit, insert the brackets provided into the seats on either side of the case.
To mount two or more units side by side, respect the cut-out dimensions shown in the drawing.
APPLICATION: The regulator is intended for industrial applications compliant with
and EN 61000-6-4.
MAINTENANCE: The device is maintenance-free.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene, etc.).Use of these
solvents can reduce the mechanical reliability of the device. Use a clothdampened in ethyl alcohol or
water to clean the external plastic case.
SERVICE: LEISTER has its own service department.
CPU
DISPLAY
15
70
45
45
For correct and safe
installation, follow the
instructions and observe
the warnings contained
in this manual.
Device structure
OUT4
POWER
Display
Keys
Accuracy
Main input
(settable digital filter)
Type TC Thermocouples
(ITS90)
Cold junction error
RTD type (scale configurable within indicated range,
with or without decimal point) (ITS90)
70
Max line resistance for RTD
PTC / NTC
Safety
°C / °F selection
Linear scale ranges
Controls
pb - dt - it
Action
Control outputs
Maximum power limit heat
Cycle time
Main output type
Softstart
Fault power setting
Standby-funktion
3 Configurable alarms
!
Alarm masking
Type of relay contact
Logic output for static relays
Transmitter power supply
Analogue retransmission signal
Power supply (switching type)
Faceplate protection
Working / Storage temperature range
EN 61000-6-2
Relative humidity
Environmental conditions of use
Installation
Weight CSS EASY
CSS
KSR Digital
FUNCTION
Power supply cable
Relay output cable
TC input
Pt100 input
POWER- board
Select transmitter
voltage
OUT4-board
S open
Power output signal
S closed
Voltage output signall
CPU- board
Select signal at
contact 3

TECHNICAL SPECIFICATIONS

2 x 4 digits, 7-segment-LED display, green,
height 10 and 7mm
4 mechanical keys (Man/Aut, INC, DEC, F)
0.2% full scale ± 1 digit at
25°C room temperature
TC, RTD, PTC, NTC
60mV,1V Ri≥1MΩ; 5V,10V Ri≥10KΩ; 20mA Ri=50Ω
Sampling time 120 msec.
Type TC Thermocouples : J,K,R,S,T (IEC 584-1, CEI EN
60584-1, 60584-2) ; custom linearization is available
/ types B,E,N,L GOST,U,G,D,C are available by using the
custom linearization.
0,1° / °C
DIN 43760 (Pt100), JPT100
20Ω
990Ω 25°C / 1KΩ 25°C
detection of short-circuit or opening of probes,
LBA alarm, HB alarm
configurabile da tastieraconfigurable from faceplate
-1999 to 9999 with configurable decimal point position
PID, Self-tuning, on-off
0,0...999,9 % - 0,00...99,99 min - 0,00...99,99 min
Heat
on / off, continuous
0,0...100,0 %
0...200 sec
relay, logic, continuous (0....10V / 4...20mA)
0,0...500,0 min
0,0...100,0 %
Actual value display, controller deactivated
Up to 3 alarm functions assignable to an output,
configurable as: maximum, minimum, symmetrical,
absolute/deviation, LBA, HB
- exclusion during warm up
- latching reset from faceplate or external contact
NO (NC), 5A, 250V/30Vdc cosϕ=1
24V ±10% (10V min zu 20mA)
15/24VDC, max 30mA short-circuit protection
10V/20mA Rload max 720Ω resolution 12 Bit
100... 240 V AC ±10%
50/60 Hz, max. 8VA
IP65
0...50°C / -20...70°C
20...85% nicht kondensierend
for internal use only, altitude up to 2000m
Panel, plug-in from front
450 g
200 g
450 g
EMC conformity has been tested with the following connections
CABLE TYPE
1 mm
2
1 mm
2
0,8 mm
2
1 mm
2
Identification of boards
CABLE LENGTH
1 m
3,5 m
compensated 5 m
3 m
S
15