Zephyr Anzio Island ZAZ-M90CS Guide D'utilisation, D'entretien Et D'installation page 8

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

D
n .
m i
E
n .
m i
x . F
m a
A : Minimum Ducted Hood Height
B : Minimum Recirculating Hood Height
C : Maximum Hood Height
D : Minimum Ducted Ceiling Height
E : Minimum Recirculating Ceiling Height
F : Maximum Ceiling Height
Standard Duct Cover
ZAZ
ZLC
A
31-
"
29"
1/2
36"
32-
"
B
1/2
C
50"
46-
"
1/2
D
93-
" (7' 9-
")
91" (7' 7")
90" (7' 6")
1/2
1/2
E
98" (8' 2")
93" (7' 9")
94-
" (7' 10-
")
1/2
1/2
120" (10')
F
116-
" (9' 8-
")
109" (9' 1")
1/2
1/2
Extension Duct Cover
ZAZ
ZLC
A
47"
47"
51"
B
51"
C
80"
80"
D
109" (9' 1")
109" (9' 1")
112-
E
113" (9' 5")
113" (9' 5")
112-
F
150" (12' 6")
150" (12' 6")
150" (12' 6")
A
n .
m i
B
n .
m i
x . C
m a
i n .
" m
a x .
2 6
" m
3 4
"
3 6
ZRM
ZRE
28"
28-
"
1/2
31"
28-
"
1/2
39"
39"
90-
" (7' 6-
")
1/2
1/2
90-
" (7' 6-
")
1/2
1/2
109" (9' 1")
ZRM
ZRE
50-
"
48-
"
1/2
1/2
50-
"
48-
"
1/2
1/2
80"
78"
" (9' 4-
")
110-
" (9' 2-
")
1/2
1/2
1/2
1/2
" (9' 4-
")
110-
" (9' 2-
")
1/2
1/2
1/2
1/2
148" (12' 4")
6
www.zephyronline.com
DUCTING
A minimum of 6" round duct is recommended to
Always use rigid type metal ducts only. Flexible
ALWAYS, when possible, reduce the number of
transitions and turns. If a long duct run is required,
increase duct size from 6" to 7" or 8".
If turns or transitions are required: Install as far
away from duct opening and as far apart between
the two transitions as possible.
Minimum mount height between range top to hood
bottom should be no less than 26".
Maximum mount height should be no higher than
34".
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
mounted too high will be hard to reach and will
If available, also refer to range manufacturer's
height clearance requirements and recommended
heights up to 12 feet. Turn to page 24 for part
number and ordering information.
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before
installation.
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for
repair or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
be made by arrangement between customer
and installer.

Publicité

Table des Matières
loading

Table des Matières