Electrical Connection - Scheppach JS600 Traduction De La Notice Originale

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

• To remove the saw blade, proceed in reverse order.

Setting the soleplate (fig. 3)

• Use the Allen wrench (11) to loosen the screw se-

curing the soleplate (10).

• Move the soleplate (5) into the desired locking posi-

tion.

• Re-tighten the screw securing the soleplate (10).

Adapter for dust extraction (fig. 1)

• Connect your jigsaw to a vacuum cleaner using the

adaptor for dust extraction (4). This will provide ex-

cellent dust extraction on the work piece. The ben-

efits are that you will protect both the equipment

and your own health. Your work area will also be

cleaner and safer.

• Dust created when working may be dangerous. Re-

fer to the section entitled "Safety instructions".

• Fit the vacuum tube of the vacuum cleaner onto the

adaptor opening (4). Check that the connections

are air-tight.

Operation

On/Off switch (fig. 1)

To switch on:

Press the On/Off switch (1)

To switch off :

Release the On/Off switch (1)

Locking button (fig. 1)

You can lock the On/Off switch (1) using the locking

button (3) when the equipment is in operation. To

switch off the equipment, press the On/Off switch (1)

briefly.

Electric speed selector (fig. 1/pos. 1)

You can pre-select the required speed with the speed

selector. Turn the speed selector in PLUS director to

increase the speed and turn the speed selector in MI-

NUS direction to reduce the speed. The appropriate

stroke speed depends on the material you want to

cut and on the working conditions. The general rules

for cutting speeds in metal also apply. While you can

generally use a higher speed with fine saw blades,

lower speeds are required for coarse saw blades.

Setting the pendulum action (fig.1)

• The strength of the pendulum action of the saw

blade can be adjusted using the selector switch for

pendulum action (6).

• You can adjust the cutting speed, cutting perfor-

mance and appearance of the cut to the work

piece you want to saw.

Set the selector switch for pendulum action (6) to one

of the following positions:

Position 0 = no pendulum action

Material: Rubber, ceramic, aluminium, steel

Please note: For fine clean cuts, thin materials (e.g.

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

sheet steel) and hard materials.

Position 1 = small pendulum action

Material: Plastic, wood, aluminium

Please note: For hard materials

Position 2 = medium pendulum action

Material: Wood

Position 3 = large pendulum action

Material: Wood

Please note: For soft materials and sawing along the

grain

The best combination of speed and pendulum action

depends on the material you want to saw. We recom-

mend you to make a trial cut on a waste piece in

order to check the ideal settings.

Making cuts (fig. 1)

• Ensure that the On/Off switch (1) is not depressed.

Only then should you connect the mains plug to a

suitable socket.

• Do not switch on the jigsaw until you have fitted a

saw blade.

• Use only saw blades that are in perfect condition.

Replace blunt, bent or cracked saw blades imme-

diately.

• Place the saw foot flat on the work piece you want

to saw. Switch on the jigsaw.

• Allow the saw blade to accelerate until it reaches

full speed. Then slowly move the saw blade along

the cutting line. Exert only gentle pressure on the

saw blade as you do so.

• When cutting metal, apply a suitable coolant along

the line you want to cut.

Sawing out sections

Drill a 10 mm hole in the section you want to saw out.

Insert the saw blade into this hole and start to saw out

the required section.