Rear Panel - Evh ICONIC Serie Mode D'emploi

N. POWER INPUT: Connect included power cord to amplifier
here, in accordance with the voltage and frequency ratings list-
ed on rear panel of amplifier. Power input's integral fuse holder
houses a spare fuse. Replace only with a fuse of the same cur-
rent and voltage rating as printed on the back of the amplifier.
O. POWER: Turns amplifier on and off. After turning this switch
ON, wait 30 seconds for tubes to warm up, then turn STANDBY
switch (P) to ON to take amp out of STANDBY mode. When
turning amplifier off, place amp in STANDBY mode by turning
STANDBY switch OFF for 10 seconds before turning POWER
switch OFF.
P. STANDBY: Place this switch in OFF position to put ampli-
fier in STANDBY mode. This should be done when taking
a break from playing or before turning amplifier off. Using
STANDBY mode prolongs tube life.
Q. POWER LEVEL SWITCH: Selects full (40W) or 1/4 (10W) power.
R. POWER AMP MUTE SWITCH: Mutes power amplifier when
engaged, enabling speaker-emulated XLR output for quiet
recording. When mute is engaged, amplifier can be operat-
ed with no speaker connected; however, note that a speaker
should be connected when power amp mute is not in use.
S. SPEAKER EMULATED XLR: For connecting amplifier
directly to sound reinforcement or recording equipment.
Speaker emulator circuit changes amp's tone to match
speaker's contribution to overall amp tone. Feature is
designed to sound like the 5150 Iconic 4X12 speaker cabi-
net, using analog circuitry to avoid latency or lag.
T. XLR GROUND LIFT SWITCH: For alleviating ground loop
hum when connected to sound reinforcement or recording
equipment.
U. PREAMP OUTPUT: For connection to effects return or power
amp input on another amplifier for simultaneous multiple
amp use. Also used to send preamp signal directly to a mixer.
V. EFFECTS LOOP: Connect SEND to external effect input;
connect RETURN to external effect output. Effects RETURN
can also be used as an input for an auxiliary preamp bypass-
ing this amplifier's preamp, while still allowing use of foot-
switchable BOOST VOLUME (J), REVERB (K), RESONANCE (L)
and PRESENCE (M) controls and POWER LEVEL SWITCH (O).
W. FOOTSWITCH: Connect included footswitch here (see
illustration at right). Footswitch enables easy selection
between channels 1 and 2 and activates boost system.
Footswitch boost includes a fixed-gain input boost and
the BOOST VOLUME control (J) for increased volume
when soloing. When connected, footswitch disables
front-panel CHANNEL ONE/TWO SELECT pushbutton (B).

REAR PANEL

REAR PANEL
X. LOAD IMPEDANCE: Selects amp output impedance (4, 8
or 16 ohms) to match speaker load. NOTE: If using the recom-
mended 5150 Iconic 4X12 speaker enclosure, set switch to "16Ω."
Y. SPEAKER OUTPUTS: For connection to speaker cabinet(s).
Either jack can be used when using only one speaker cabi-
net. Use only high-quality unshielded speaker cables.
NOTE: A speaker must always be plugged into one of the
speaker jacks when the amplifier is on and POWER AMP
MUTE SWITCH (S) is disengaged, or damage may occur. Turn
amplifier off or put it in STANDBY mode when changing
speaker connections or impedance settings
SPEAKER
OUTPUT 1
TYPE
POWER REQUIREMENT
OUTPUT
INPUT IMPEDANCE
OUTPUT IMPEDANCE
FUSES
FOOTSWITCH
TUBES
DIMENSIONS AND WEIGHT
Product specifications subject to change without notice.
2
IMPEDANCE
SPEAKER
OUTPUT 2
16Ω NONE
16Ω 16Ω
8Ω NONE
8Ω 8Ω
4Ω NONE
SPECIFICATIONS SPECIFICATIONS
PR 6047
250 watts
10 to 40 watts RMS into 4, 8 or 16 ohms
240KΩ
4, 8 or 16 ohms (selectable)
F4A L 250V (100V and 120V units)
F2A L 250V (220-240V units)
Two-button (included)
Two 6L6GC power amp tubes
Two ECC83S/12AX7 preamp tubes
Height: 20" (50.8 cm)
Width: 22.5" (57.2 cm)
Depth: 11.25" (28.6 cm)
Weight: 53 lbs. (24 kg)
SETTING
16Ω
8Ω
8Ω
4Ω
4Ω