Unitor BA210D Сonversion Des Instructions De Fonctionnement Original page 11

INFORMATOIN NOISE / MEAN ACCELERATION VALUE
The tools are suppressed in accordance for the prevention and elimination of radio
disturbances measured in accordance with standard: EN 60745
Sound pressure level / Sound power level
L PA L WA
dB(A)
BA210D 90 101
DANGER
The indicate measurements refer to new power tools.
Daily usa causes the noise and vibration values to change.
Displayed emission values are comparative and are to be employed for
a provisional assessment of the operator's risk exposure during the work period.
Appropriate evaluation of work period must also include tool's idle and stop
periods. These emission values represent the tool's main applications.
If the tool is used for other applications, with other accessories, or if it does not
undergo regular maintenance, emission values can significantly increase
during operations.
Use hearing protection!
PARTS OF THE TOOL
1 - Technical data identification label
2 - ON/OFF switch
3 - Wheel spindle locking button
4 - Wheel spindle
5 - Auxiliary handle
6 - Adjustable protective shield
7 - Collar with protective shield fixing points
8 - Protective shield fixing screws
9 - Wheel mounting ring
10 - Abrasive wheel lock nut
11 - Motor ventilation slots
12 - Wrenches
STARTING UP
WARNING
Pay attention to the mains voltage! The mains voltage must
correspond to the voltage indicated on the technical data identification
label (1).
DANGER
Before any intervention on the electrical tool take the plug
out from the socket
3 axis vibration level
(Surface grinding)
a h
Uncertainty Uncertainty
m/s 2
3 5,50 1,5
BEFORE STARTING THE TOOL
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been damaged
during storage or transport;
- the tool is complete; check that the number and type of components comply
with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in the table
and that indicated on the tool identification plate reproduced;
- the power supply cable and plug are in perfect condition;
- the ON/OFF switch (2) works properly though with the power supply
disconnected;
- the wheel spindle locking button (3) is released (rotate the abrasive wheel by
hand for at least one revolution);
- all the parts of the tool have been assembled in the proper manner and that
there are no signs of damage;
- the ventilation (11) slots are not obstructed.
ASSEMBLING THE TOOL
DANGER:
never work without protective earmuffs (6)
Wear protective gloves!
- screw in the auxiliary handle (5); the handle can be mounted on the left or
right of the tool body;
- mount the protective protective shield (6) with collar (7) on the body of the tool
using the screws (8). Ensure that the protrusions on the collar are inserted in
the slots cut into the flange of the shield;
- after tightening the screws (8) and collar (7), the shield must be able to rotate
with a slight resistance approximately 20° in order that it may be positioned as
desired by the operator.
The adjustable protective shield must be mounted around the
handle
ASSEMBLY/REPLACEMENT OF THE GRINDING WHEELS
ASSEMBLY OF THE GRINDING WHEELS:
1.Insert the wheel guide ring (9), checking that it is properly housed in its seat;
2.insert the abrasive wheel;
3. s crewandtightenthelocknut(10)usingthepinwrench,preventingthespindle
formmovingusing(12)spannerorthespindlelockingbutton.
FITTING AND REPLACING ABRASIVE WHEELS
This can be done in one of two ways:
1. Mode: Lock the wheel spindle (4) y pressing button (3), while at the same time
rotating thewheel until it locks position. Unscrew the locking ring using the
pin wrench, replace the wheel, re-tighten the locking ring. Unlock the wheel
spindle by releasing the buttonand rotate the wheel by hand to ensure that it
runs freely.
.
11