102 Setting The Time And Date - Unity I UT3K Manuel D'utilisation

8 If you plan to use the CheckUPS software that came with your UPS, connect the interface cable from the UPS to
E
the computer system, with the "UPS" end connected to the UNITY/I.
N
Using CheckUPS with Windows 95: Shut down your computer and insert the CheckUPS CD. Restart the
G
computer. Follow the instructions in the CheckUPS package.
L
Using CheckUPS without Windows 95: Start the computer and follow the instructions in the CheckUPS package.
I
S
Fill out the warranty registration card in this manual and return it to Best Power. Please return the registration card
9
H within ten days of installation.

102 Setting the Time and Date

The UPS stores the time, date, and year in parameters that you can program (see Section 300 for more about
parameters). These parameters must be programmed correctly so that the UPS can store accurate information in its
alarm and system logs. Whenever the UPS has been shut down, you should reset the time and date after you restart the
UPS. To set the time, date, and year parameters, follow the steps below.
Note: When the unit is in parameter mode, the functions of the front panel keys change. The label inside the front door
of the unit explains what the keys do when the UPS is in parameter mode. The label also shows a
"Programming Template" with different key names for parameter mode.
1. To enter the parameter mode, hold down the [
display changes to P-00 (for parameter 0).
2. Enter the user password (377) by following these steps:
a. Press [
b. Use the [%
to go back.
Note: If you hold down the [%
c. Press [
d. Press [
3. Set the year (parameter 91) by following these steps:
a. Use the [%
b. Press [
c. Use the [%
d. Press [
e. Press [
4. Set the date (parameter 90) by following these steps:
a. Use the [
b. Press [
c. Use the [%
the date were March 27, you should enter "0327."
d. Press [
e. Press [
5. Set the time (parameter 89) by following these steps:
a. Use the [
b. Press [
c. Use the [%
from 1 p.m. to 11:59 p.m., add twelve to the hour. For example, 2:30 p.m. would be 14:30.
d. Press [
e. Press [
6. To escape the parameter mode, press [VLINE] twice.
]. The display should show 0 (the value of parameter 0).
CANCEL
] key to change the display to 377. If you accidentally scroll past 377, use the [
LOAD
LOAD
seconds.
]. The display should show I to show you have entered the user password.
RUNTIME
]. The display should show P-00.
CANCEL
] key to change the display to P-9I.
LOAD
]. The display should show a year.
CANCEL
] or the [ ] key to change the display to the correct year.
LOAD VOUT
]. The display should show the correct year.
RUNTIME
]. The display should show P-91.
CANCEL
] key to change the display to P-90.
VOUT
]. The display should show a date formatted as mm.dd (month.day).
CANCEL
] or [ ] key to change the display reading to the correct month and day. For example, if
LOAD VOUT
]. The display should show the correct date (mm.dd).
RUNTIME
]. The display should show P-90.
CANCEL
] key to change the display to P-89.
VOUT
]. The display should show a time formatted as hh:mm (hour:minute).
CANCEL
] or [ ] key to change the display reading to the correct time in 24-hour time. For times
LOAD VOUT
]. The display should show the correct time (in 24-hour time).
RUNTIME
]. The display should show P-89.
CANCEL
] and [ ] keys together. Release the keys when the
CANCEL RUNTIME
] or the [ ] key, the display will scroll more quickly after a few
VOUT
6
] key
VOUT