Troubleshooting Guide; The Device; Customer Service Department; Warranty - Kärcher Puzzi 10/1 Manuel D'instructions

Clean the nozzle
1. Unscrew the union nut.
2. Clean the nozzle mouthpiece.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
The device is not working
1. Check the socket and the power supply fuse.
2. Check the mains cable and the mains plug of the de-
vice.
3. Switch on the device.
No water emitted from the nozzle
1. Fill up the fresh water tank.
2. Check the couplings on the spray hose for correct
seating.
3. Clean or replace the nozzle mouthpiece.
4. Clean the fresh water filter.
5. Spray pump defective, contact customer service.
Single-sided spray jet
1. Clean the nozzle mouthpiece.
Poor suction performance
1. Check that the cover is seated correctly.
2. Clean the seal on the cover and the contact surface
on the device.
3. Clean the fluff filter.
4. Check the suction hose for clogging; clean if neces-
sary.
Spray pump is loud
1. Refill the fresh water tank.
Heavy foaming in the wastewater container
1. Add defoaming agent in the wastewater container or
fill up the defoaming agent container.

Customer Service department

If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in circu-
lation by us. This declaration is invalidated by any chang-
es made to the machine that are not approved by us.
Product: Spray retraction device
Type: 1.100-xxx
Type: 1.193-xxx
Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2011/65/EU
2014/30/EU
Harmonised standards used
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60335-1
EN 60335-2-68
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
National standards used
-
The signatories act on behalf of and with the authority of
the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01
Declaration of Conformity (UK)
We hereby declare that the product described below
complies with the relevant provisions of the following
UK Regulations, both in its basic design and construc-
tion as well as in the version put into circulation by us.
This declaration shall cease to be valid if the product is
modified without our prior approval.
Product: Spray retraction device
Type: 1.100-xxx
Type: 1.193-xxx
Currently applicable UK Regulations
S.I. 2008/1597 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2016/1091 (as amended)
Designated standards used
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60335-1
EN 60335-2-68
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
National standards used
-
The signatories act on behalf of and with the authority of
the company management.
English 13