QSC K Serie Manuel D'utilisation page 20

Specifications
Configuration
Transducers
Low-frequency
High-frequency
Frequency Response (-6 dB) 66 Hz – 18 kHz
Frequency Range (-10 dB)
ENG
Nominal Coverage (-6 dB)
Maximum SPL (1 meter)
Amplifiers
Power Output
Input Impedance (Ω)
Controls
Indicators
Connectors
Cooling
Amplifier Protection
Transducer Protection
AC Power Input
AC Power Consumption
1/8 Power
Enclosure
Finish
Grille
Dimensions (HWD)
Weight (Net)
Available Accessories
Specifications subject to change without notice.
K8 K10
Trapezoidal 2-way Multipurpose 2-way
8" cone transducer 10" cone transducer
1.75" diaphragm compression driver 1.75" diaphragm compression driver
60 Hz – 18 kHz
61 Hz – 20 kHz 56 Hz – 20 kHz
105° conical 90° conical
127 dB peak 129 dB peak
1000 W Class D
XLR / ¼": 40k balanced / 20k unbalanced • XLR / ¼" MIC mode: 2260 balanced • RCA: 10k
Power • Gain A • Gain B • Mic/Line • LF Mode (Ext Sub/Norm/DEEP™) • HF Mode (Flat/Vocal Boost)
Front LED (On/Off/Limit)
Power • Signal A • Signal B • Standby • Limit • Mic
Balanced female XLR / ¼" line/mic level input • Balanced female XLR / ¼" line level input • Dual Balanced male XLR
full range line level out • Balanced male XLR "mix" out • Stereo RCA line level input • Remote gain control • Locking
IEC power connector
On demand, 50 mm variable speed fan
Thermal limiting • Output overcurrent • Overtemperature muting • GuardRail™
Thermal limiting • Excursion limiting
Universal power supply 100 - 240 VAC, 50 - 60 Hz
100 VAC, 2.3 A • 120 VAC, 2.01 A • 230 VAC, 1.13 A
Impact resistant ABS
Black Paint
Black powder coated 18 gauge steel
17.7" x 11" x 10.6" 20.4" x 12.6" x 11.8"
450 mm x 280 mm x 269 mm 519 mm x 320 mm x 300 mm
27 lb (12.2 kg) 32 lb (14.5 kg)
K8 TOTE • K8 YOKE • K10 TOTE • K10 YOKE •
K SERIES M10 KIT K SERIES M10 KIT
K12
Multipurpose 2-way
12" cone transducer
1.75" diaphragm compression driver
52 Hz – 18 kHz
48 Hz – 20 kHz
75° conical
131 dB peak
23.7" x 14" x 14"
603 mm x 356 mm x 356 mm
41 lb (18.6 kg)
K12 TOTE • K12 YOKE •
K SERIES M10 KIT
20
KSub
4th Order Bandpass
2 x 12" cone transducers
48 Hz – 134 Hz
44 Hz – 148 Hz
130 dB peak
Power • Gain • LF Mode (Normal/
DEEP™) • Polarity (Normal/Reverse)
• Front LED (On/Off/Limit)
Power • Signal • Standby • Limit
Dual balanced female XLR / ¼"
line level input • Dual Balanced
male XLR full range line level out •
Remote gain control • Locking IEC
power connector
Painted birch plywood
Black textured paint
26" x 14" x 28.1" (including casters)
665 mm x 356 mm x 714 mm
74 lb (33.6 kg)
KSub COVER