Sera LED Moonlight Set Mode D'emploi page 11

sera LED moonlight
The LED lamp can be attached to the aquarium glass
or any other smooth surface by means of the two in-
cluded double suction cup holders. The lamp should
be installed above the water surface. The sera LED
moonlight can also be integrated into an overtank
luminaire such as the sera LED fiXture. The clips re-
quired to do so are available in pairs as accessories.
A special silver moon foil is also included. It can be
attached to the glass tube for making the light appear
more diffuse. This is suitable for very small tanks or
to further lower the light intensity.
Operation
Connect the mains plug to the mains supply only after
all components have been connected appropriately
and everything is firmly installed.
1. ON/OFF
Press the "MINUTE/ " key to switch the light on or
off.
2. Adjusting the actual time
Press the "SET" key for approximately 3 seconds.
The display will then start to flicker. Then press the
"HOUR" key (for adjusting the hours) and "MINUTE"
(for adjusting the minutes) to set the actual time. Sin-
gle clicks on these keys will increase the displayed
digit by 1 every time. If keys are held down, the num-
bers in the display start to run upwards quickly. Con-
firm these settings by pressing the "SET" key, and
you will proceed to the next setup step – Program-
ming the moonrise (see item 3, please).
3. Programming the moonrise
Press the "SET" key for approximately 3 seconds.
The display will then start to flicker. Then briefly press
the "SET" key once. Now the display will show "ON"
for the moonrise. The display will then immediately
switch into input mode. You can set the begin of
the moonrise as desired by pressing the "HOUR"
and "MINUTE" keys (please see item 2, Adjusting
the actual time). Confirm these settings by pressing
the "SET" key, and you will proceed to the next setup
step – Programming the moonset (please see item 4).
4. Programming the moonset
Press the "SET" key for approximately 3 seconds.
The display will then start to flicker. Then briefly press
the "SET" key twice (ON » OFF). Now the display
will show "OFF" for the moonset. The display will
then immediately switch into input mode. You can
set the begin of the moonset as desired by pressing
the "HOUR" and "MINUTE" keys (please see item 2,
Adjusting the actual time). Confirm these settings by
pressing the "SET" key, and you will proceed to the
next setup step – Adjusting the switch mode (please
see item 5).
5. Adjusting the switch mode
Press the "SET" key for approximately 3 seconds.
The display will then start to flicker. Then briefly press
the "SET" key three times until the display shows "F-"
in the order (ON »OFF » F). You can now select the
switching mode (F1 – F3). You can switch the pro-
grams in the order F1, F2, F3, F1, F2 ... by repeatedly
pressing the "HOUR" key. Confirm these settings by
pressing the "SET" key, and you will proceed to the
next setup step – Setting the moon phase (please
see item 6).
You can choose between the following programs:
Description of the programs F1 – F3
Program Function
F1 Moonrise and moonset with
clear sky according to lu-
nation
F2 On/Off
F3 like F1, plus Cumulus cloud
simulation
(* The dimming phase may be shorter in programs
with low brightness.)
In program F3, the lighting is reduced to 10% of the
adjusted light brightness every 20 minutes for slightly
more than a minute. However, this cloud scenario
begins only one hour after moonrise.
6. Setting the moon phase – selecting the day
The programmed moon calendar begins with full
moon, unless you select another day in the moon
calendar.
You must select the day in the programmed syn-
odical calendar if you wish to operate the sera LED
Digital Moonlight Timer according to the actual
moon phases. Day 1 represents "full moon", and
day 15 is "new moon". The time between full moon
and new moon is called waning moon (chart symbol:
), after new moon it is called waxing moon (chart
symbol: ). The current moon phase is easy to find
on the Internet using "moon calendar" as a keyword.
11
Description
Dimming up and down from
0 – 100% – 0%, each
lasting 30* minutes at the
maximum
Switching on and off
automatically without
dimming
Smooth reduction to 10%
of the adjusted brightness
(every 20 minutes for 90
seconds)