DS Produkte LXA-HW1185-10W Mode D'emploi page 4

EN
The precondition for the installation of the fl oodlight is an
existing, properly connected distribution box.
1. Open the distribution box.
2. Insert the cable (2) of the fl oodlight into the distribution box. It
may be necessary to remove the terminal strips from the cable
fi rst.
3. With the aid of the terminal strips you clamp the leads (brown,
blue, green/yellow) to the corresponding connections in the dis-
tribution box.
Brown L live conductor
Blue N neutral conductor
Green/yellow protective earthing conductor
Settings
You can adapt the functions of the motion detector to your require-
ments. For this purpose you will fi nd three setting knobs on the
base of the motion detector (4):
• SENS (sensitivity and movements): Turn the knob towards +
to increase sensitivity. The motion detector then reacts to the
slightest movements. In order to reduce sensitivity, turn the
knob towards -.
Under certain circumstances it may be necessary to adjust
sensitivity in relation to seasonal temperature fl uctuations.
• TIME (lighting duration): This button enables you to set the
length of time the fl oodlight should stay on after motion has
been detected. Turn it towards + to increase lighting duration
and towards - in order to reduce it. The lighting time can be
adjusted from 10 seconds to 10 minutes.
• LUX (twilight switch): This button sets the ambient lighting con-
ditions from which the motion detector is activated. Turn the
knob towards for a higher lighting value (e.g. if the motion
detector is to react during daylight, too). The further you turn it
towards , the darker the surroundings have to be to activate
the motion detector and the fl oodlight.
Positioning
Position the fl oodlight and the motion detector.
1. The fl oodlight can be adjusted steplessly up and down. You can
tilt it until it reaches the desired angle.
2. When it is horizontal the max. forward range of the motion de-
tector is 10 m. Tilting the motion detector downwards reduces
the range (e.g. in order to avoid undesired detection of move-
ments in the street).
In order to adjust the motion detector vertically you release the
setting screw (3), move the motion detector to the required po-
sition, and then tighten the screw again.
3. To the sides the motion detector has a detection range of 180°.
You can turn it steplessly to the right or left, in order to adjust
the detection area to your requirements.
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
01219_de-en-fr-nl_A4_V1.indb 4 01219_de-en-fr-nl_A4_V1.indb 4
Trouble-shooting
If the article is not functioning correctly, please check fi rst whether
you can correct the problem yourself.
Do not attempt to repair a defective electrical device
yourself!
If the fl oodlight doesn't switch on, ...
• it may be the case that the fuse is defective or you have a
power supply problem.
• the motion detector may be aligned in such a way that the re-
quired detection area is outside the range of the motion detec-
tor.
If the fl oodlight switches on with a time delay (the range is too
close), this can have the following causes:
• the motion detector reacts with a time delay to movement from
the front. It reacts faster to persons approaching from the sides.
• the temperature difference between the person and the sur-
roundings is too low.
If the fl oodlight switches on without any apparent reason, this can
have the following causes:
• exhaust fans, e.g. from cooker hoods or clothes dryers (move-
ment of warm air)
• passing vehicles (warm engines)
• nearby trees or bushes
• sudden changes in surrounding temperatures or gusts of wind
If the fl oodlight also switches on during the day even though the
twilight switch is set to
shade (e.g. under a roof or a tree).
Technical Data
Article number:
Model No.:
Power supply:
Power:
Protection class:
Type of protection:
Detection fi eld:
Range:
Light source:
Light fl ux:
Light colour:
Colour rendering index:
Time setting:
Recommended mounting height:
Disposal
The packaging material is recyclable. Please dispose of it
in an environmentally friendly manner and take it to a recy-
cling centre.
Dispose of the device in an environmentally friendly man-
ner. It should not be disposed of in the normal domestic
waste. Dispose of it at a recycling centre for used electri-
cal and electronic devices. You can obtain more information
from your local authorities.
Customer Service / Importer:
All rights reserved.
Instructions
, the reason for this may be that it is in the
Z 01219
LXA-HW1185-10W
100 – 240 V~ 50/60 Hz
max. 10 W
I
IP44
max. 180 °
max. 10 m
LED (not replaceable)
650 lm
6000 K
70 R
a
approx. 10 s – 10 min,
steplessly adjustable
at least 2 m
✆
+49 38851 314650 *)
Z 01219_V1_07_2015
20.07.2015 10:33:14 20.07.2015 10:33:14