LAS BC260 Manuel De L'opérateur page 5

Tilting adapter BC260
TABLE OF CONTENTS
1. PACKAGE CONTENTS
2. INTRODUCTION
3. INTENDED USE
4. SPECIFICATIONS
5. SAFETY GUIDELINES
6. INSTALLATION
7. OPERATION
8. MAINTENANCE
9. WARRANTY
10. CONTACT INFORMATION
1. PACKAGE CONTENTS
1 x Tilt Adapter Left
1 x Tilt Adapter Right
4 x Allen screw M8 x 25
4 x Washer M8
2. INTRODUCTION
Congratulations on choosing the tilting adapter BC260. This has been pro-
duced according to very high standards and has undergone careful quality
control procedures.
Does the caravan have a hinged storage door and does the BC260 not extend
far enough to open this door completely? The tilting adapter BC260 is the
ideal solution! This tilting adapter can be easily attached between the sli-
ding platform and the bicycle carrier. This also allows the extended BC260 to
tilt so that the hinged caravan storage door can be opened completely. The
tilting adapter BC260 is very light and is very easy to assemble.
The connection cable with handle makes it possible to operate the tilt func-
tion with one hand, while the other hand tilts the carrier. The caravan draw-
bar storage door can now open completely and the drawbar storage is easily
accessible.
Please read this manual very carefully and familia-
rize yourself with all safety precautions before pro-
ceeding with the installation and use of this tilting
adapter BC260.
Important! Keep this manual for future reference.
Hand this manual over to the new owner when sel-
ling the tilting adapter BC260 or the caravan!
3. INTENDED USE
The tilting adapter BC260 is attached between the BC260 platform and bicy-
cle carrier.
For caravan with hinged storage door and/or in case of sliding range limiting
conflict between BC260, nose wheel and/or handbrake handle.
4. SPECIFICATIONS
Type: suitable for BC260
Weight: approx. 2kg
Maximum load: 65kg
5
5
5
5
5
5
6
7
7
7
4 x Spring washer M8
1 x Connection cable with handle
1 x Allen key
1 x Assembly instruction
5. SAFETY INSTRUCTIONS
Read this manual carefully before installing and
using the tilting adapter BC260 for the first time.
Follow the fitting instructions carefully. Failure to
follow the instructions can lead to personal injuries
and material damage.
The symbols below represent important points of
attention.
PAY ATTENTION! WARNING! CAUTION! SAFETY ABOVE
EVERYTHING! IMPORTANT INFORMATION!!
NOTE: Useful tip. Facilitates the operation or fitting
of the product or serves for better understanding.
Before starting installing the tilting adapter BC260:
Only use adapters and accessories that are supplied or recommended by the
manufacturer.
Make sure the BC260 bicycle carrier is in good condition without any dama-
ge and is free from rust, dirt etc.
Do not remove, change or alter any parts of the BC260 bicycle carrier. Any
drilling of holes is not allowed.
Stop work immediately if you are in doubt about the assembly or any pro-
cedures. In doubt, always consult your dealer or one of our technical people,
find the contact details on the last page of this manual.
Do not install or use the tilting adapter BC260 if you are under the influen-
ce of drugs, alcohol or medication that could impair your ability to use the
equipment safely.
6. INSTALLATION
Carefully follow the instructions for use with the
instructions contained therein. Failure to follow the
instructions could result in personal injury or mate-
rial damage.
If you are not sure whether you have carried out the installation of the tilting
adapter correctly, ask your dealer or the manufacturer for further informa-
tion. Neither the manufacturer nor suppliers are liable for damage that can
be attributed to improper use or incorrect assembly.
Place the caravan (or only the BC260) on a hard, level surface. The tilting
adapter BC260 is easy to mount and comes complete with mounting mate-
rial. Remove all parts from the packaging and arrange them clearly. Check
the contents on the basis of the package contents overview at the front of
the manual.
First, remove the bicycle carrier from the sliding platform
First, loosen the 4 Allen screws (1.) using the Allen key supplied and remove
the bolts (2.).
The bicycle carrier part can be removed (3.).
5