Led Lenser X21.2 Mode D'emploi page 4

LED LENSER® * X21
We are delighted that you have purchased one of our products.
These are usage instructions to help you familiarize yourself with
your new purchase. All the documents accompanying the product
must be read attentively before using the product, stored for future
use and if the product is transferred to a third party, the documents
should be handed over as well. This ensures that maximum
benefit is drawn from the product and questions from users can be
resolved when they arise.
Above all, comply with the warnings and safety instructions and
dispose of the packaging material properly.
Before the first use, unscrew the battery compartment and remove
the plastic cover at the rear end of the torch and insert 4 fresh
D-cell batteries. After inserting the batteries, re-attach the battery
compartment cover before pushing the switch button, otherwise
the lamp might not work properly.
Product
LED LENSER
9421 LED LENSER® X21.2
Version of the operating manual: 1.2
1. Battery:
4 × Alkaline battery 1.5 V (D-cell, LR20)
(1.2 V NiMH rechargeable batteries could also use; not included)
2. Switching on and off
In the front section of the X21.2, directly behind the wide head, the
switch button is located. This switch button can be used to select
different Light Functions (see Point 5).
Please note that there are 2 ways to use the switch button:
2.1 Switching
When the switch button is pressed beyond the pressure point,
(deep enough so that the switch locks into position) a small clicking
sound can be heard.
2.2 Tapping
When the switch button is only tapped briefly but not as deeply as
explained above. As a result, the switch does not lock into position,
there is no audible click and the switch returns to its untouched
starting position when released.
To turn on the X21.2 use the switch button as described in 2.1.
In order to use the Light Functions please read Section 5 "Light
Functions".
3. Focus
The focus of the X21.2 can be quickly adjusted with the Speed
Focus feature. For this purpose, hold the torch on the serrated
middle section firmly with one hand and, with the other hand, pull
the reflector lens of lamp head forwards or backwards. By doing
this, you can adjust the light beam continuously to suit your needs.
4. Smart Light Technology (SLT)
The X21.2 is equipped with our Smart Light Technology (SLT).
Thanks to the use of a microcontroller, the light output of the LED
can be controlled and different Light Functions can be utilized.
By using a single switch it was possible to design the interface to
be simple and user-friendly. The pocket torch can provide three
different Light Functions to suit your needs. To turn the torch on
and off and select the various Light Functions, the switch in the
front section of the torch should be used to do so. Here, the switch
is operated in the two ways described above in Point 2.
The brightness of the X21.2 is additionally controlled by the built-in
temperature control unit.
5. Light Functions
The 3 Light Functions are chosen using the switch button as
explained below:
03
.2
5.1. Light Program Power
The X21.2 is turned on by being pressed once. Then you have full
brightness (Power). One more push will turn the lamp off.
5.2 Light Program Low Power
If you tap the switch button on the lamp head 2 times, the X21.2 will
have reduced brightness (Low Power).
5.3 Light Program Strobe
If you tap the switch button on the lamp head 3 times and then
switch the button within one second the X21.2 is in the Light
Function Strobe and flashes quickly (Strobe).
6. Replacing the Batteries
To replace the batteries, turn off the flashlight and unscrew the cap
at the end. Take out the used batteries and dispose of it properly.
Insert the new batteries according to the polarity marks (+) and
(-). Close the flashlight by screwing the end cap back in place.
Important - when inserting the batteries, follow the polarity marks
(+) and (-) that are marked on the battery housing and match
them up with the respective markings on the battery body. If you
insert batteries the wrong way, there may be a risk of damage or
explosion!
Never try to use batteries or use fresh and used batteries together.
Always change all batteries at the same time and use high quality
batteries and the same type only. Do not use high current or
rechargeable batteries because of different electrical values.
If you do not intend to use the lamp for a long period of time,
take the batteries out to prevent battery leakage and damage to
the lamp. Discharged batteries should be taken out of the lamp
and dispose of it properly. Used batteries and accumulators are
hazardous waste and must be disposed of according to government
regulations.
Keep away from excessive heat sources while operating the lamp.
7. Cleaning
For cleaning, please use a dry, clean and lint-free cloth.
If salt water is spilled on the lamp, it must be removed immediately.
8. Scope of delivery
The X21.2 is supplied with the following accessories:
4 x Alkaline batteries 1.5 V (D-cell, LR20)
1 x operating manual
1 x carry belt
For additional accessories please see our homepage: www.
ledlenser.com.
Additional accessories for the X21.2 are available (e.g. colour filter,
etc.).
You can get information on these additional accessories on our
website at www.ledlenser.com.
9. Caution:
Do not swallow any small parts or batteries that are present.
The product or parts thereof (including batteries) must be stored
outside the reach of children.
For reasons of safety and approval (CE), the product must not be
modified and/or changed. The product is to be used exclusively as
a torch. If the X21.2 is used for any other purpose or incorrectly, it
can get damaged and a hazard-free use is no longer guaranteed
(danger from fire, short-circuit, electric shock etc.). There is then
no liability for harm to persons or damage to property, and the
warranty from the manufacturer is rendered null and void when
the product is used in an unintended manner.
The temperature range in which the X21.2 can be operated in is
between -20 C° and +50 C° (or between -4 F° and 122 F°). Ensure
that the X21.2 is not subjected to extreme temperatures, intense