Germ Guardian Clean2 GGH200 Utilisation Et Instructions D'entretien page 3

GGH200REV0108:Air Sanitizer Manual 3L ver 2
USE OF THE UV-C AIR SANITIZER
When the Germ Guardian™ UV-C Air Sanitizer is turned on you will see a ring of blue light that lets
you know it is working. The Germ Guardian™ UV-C Air Sanitizer can process 450 cubic feet of air
per hour and is effective in almost any size room. When using this product basic precautions
should be followed to reduce the risk of fire, electric shock and injury.
GETTING STARTED
1 Plug the UV-C Air Sanitizer/Hand Vac Storage Base into a 120v AC electrical outlet.
2 Turn the power switch located underneath the base. A blue ring of light will appear indicating
that the unit is on and working.
3 For best results continuous operation is recommended.
4 Place the hand vac in the base for storage and charging.
NOTE: The Germ Guardian UV-C Air Sanitizer contains no serviceable parts except its UV-C bulb.
The bulb may be removed for replacement.
To reorder the UV-C Replacement Bulb Model LB1000 please call customer service at
1-866-603-5900 or log onto www.germguardian.com.
UV-C AIR SANITIZER
Replacement Bulb LB1000
WHEN TO CHANGE THE BULB
A replaceable 3.5 watt UV-C light bulb will last over 5000 hours. Over time with use, the UV-C bulb
will lose some intensity approximately 15% at 4000 hours. Therefore it is suggested to replace the
UV-C light bulb every 8-10 months depending on use. You will know to change the bulb when the
light flickers continuously or changes color. To reorder the UV-C Replacement Bulb Model LB1000
please call customer service at 1-866-603-5900 or log onto www.germguardian.com.
1 Turn off the unit and unplug it from the electrical outlet. (Fig. 1)
2 Remove Hand Vac and using a small Phillips head screwdriver, loosen and remove the
Phillips screw located inside of the charger base. (Fig. 2)
3 Remove the top cap by lifting it off of the top of the unit. (Fig. 3)
4 Hold the unit in place with one hand. Locate the bulb and reach into the cylinder with your
opposite hand. Turn the bulb in a counter clockwise position (left) to loosen it from the
socket. (Fig. 4)
5 Take new bulb and screw into unit using a clockwise motion. (Fig. 5)
6 Wipe off finger prints with a dry cloth after bulb is installed.
7 Reassemble by reversing steps 1-6.
Fig. 1
E-4
1/3/08 2:31 PM Page 3
™
™
BULB REPLACEMENT
Fig. 2 Fig. 3
™
UV-C AIR SANITIZER
Fig. 4
STORING & CHARGING
CHARGING
NOTE: Use only the charger supplied by the manufacturer to recharge.
IMPORTANT: Before first use, charge your vacuum for at least 24 hours.
Power switch must be in the off position when unit is charging on base. If charging light is not
illuminated, press on/off button to assure unit is turned off. Remember, unit will not charge if
charging light is not illuminated.
1 Place unit in charger base when not in use.
2 Connect wall charger to the outlet.
3 Charging light will illuminate when unit is properly placed in the base. Unit will be charged
in 16-24 hours.
4 The light stays on and remains the same color even when the unit is fully charged.
STORING
Store the hand vac in the charging base on a flat surface when not in use.
DIRECTIONS FOR USE OF THE HAND VAC
1 Press the on/off button.
2 Use cleaner to remove dust, debris and dirt from counters, floors, etc.
3 Turn unit off before storing.
4 Empty and clean dirt cup and filter after each use or when cup is full.
BULB REPLACEMENT
(cont.)
Fig. 5
E-5