Napoleon Ascent 36-1 Manuel D'installation Et D'opération page 59

12.1 pilot burner adjustment
Adjust the pilot screw to provide properly sized fl ame. Turn in a clockwise direction to reduce the gas fl ow.
Check Pressure Readings:
Inlet pressure can be checked by turning screw (A) counter-
clockwise 2 or 3 turns and then placing pressure gauge tubing
over the test point. Gauge should read as described on the chart
below. Check pressure with main burner operating on "HI".
Outlet pressure can be checked the same as above using screw
(B). Gauge should read as described on the chart below. Check
pressure with main burner operating on "HI".
After taking pressure readings, be sure to turn screws
clockwise fi rmly to reseal. Do not overtorque.
Leak test with a soap and water solution.
Prior to pilot adjustment, ensure that the pilot assembly has not been painted. If overspray or painting of
the pilot assembly has occurred remove the paint from the pilot assembly, or replace. Fine emery cloth or a
synthetic scrub pad (such as Scotch-Brite™) can be used to remove the paint from the pilot hood, electrode
and fl ame sensor.
Pressure Natural Gas
(inches)
Inlet
(minimum 4.5")
Outlet
12.2 venturi adjustment
This appliance has an air shutter that has been factory set open according to
the chart below:
Regardless of venturi orientation, closing the air shutter will cause a more
yellow flame, but can lead to carbonization. Opening the air shutter will cause
a more blue flame, but can cause flame lifting from the burner ports. The flame
may not appear yellow immediately; allow 15 to 30 minutes for the final flame
colour to be established.
AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED
INSTALLER.
note:
It is important that the orifice is securely inserted into the venturi.
Natural Gas
(millibars)
*7" 17.4mb
(minimum 11.2mb)
3.5" 8.7mb
MILLIVOLT
VENTURI ADJUSTMENT CHART
FUEL TOP
NG
P 1/4" (6.3mm)
Flame must envelop
upper
3/8" to 1/2" SIT ELECTRONIC IGNITION
(12.7mm - 9.5mm) of
thermocouple
SIT ELECTRONIC IGNITION
3/8" - 1/2"
(9.5mm - 12.7mm)
Flame must envelop
upper
3/8" to 1/2"
(12.7mm - 9.5mm) of
SIT MILLIVOLT
Flame sensor
INSERT PILOT ASSEMBLY
SIT MILLIVOLT
3/8" - 1/2"
(9.5mm - 12.7mm)
MILLIVOLT
Flame must envelop
ILLUSTRATED
upper
3/8" to 1/2"
(12.7mm - 9.5mm) of
thermocouple &
PSE LONG SENSOR
thermopile
(9.5mm - 12.7mm)
PSE LONG SENSOR
Flame must envelop
Propane
3/8" - 1/2"
(9.5mm - 12.7mm) (inches)
(12.7mm - 9.5mm) of
Flame must envelop
13"
upper
3/8" to 1/2"
(minimum 11")
(12.7mm - 9.5mm) of
thermocouple
10"
*Maximum inlet pressure not to exceed 13"
B
A
PILOT SCREW
VENTURI
BURNER
REAR
1/16" (1.5mm)
3/8" (9.5mm)
La flamme doit envelopper
la thermocouple de 3/8" à
adjustment
12.0 adjustment
(9.5mm - 12.7mm)
3/8" - 1/2"
(9.5mm - 12.7mm)
Flame must envelop
upper
3/8" to 1/2"
ELECTRONIC
(12.7mm - 9.5mm) of
(9.5mm - 12.7mm)
Flame sensor
ILLUSTRATED
La flamme doit envelopper
la sonde de flamme de
(9.5mm - 12.7mm)
3/8" - 1/2"
(9.5mm - 12.7mm)
Flame must envelop
upper
3/8" to 1/2"
(12.7mm - 9.5mm) of
(9.5mm - 12.7mm)
thermocouple &
thermopile
La flamme doit
envelopper la
thermocouple et
de 3/8" à 1/2"
(9.5mm - 12.7mm)
3/8" - 1/2"
Propane
upper
3/8" to 1/2"
(millibars) (9.5mm - 12.7mm)
thermocouple
La flamme doit envelopper
32.4mb
la thermocouple de 3/8" à
(minimum 27.4mb)
(9.5mm - 12.7mm)
24.9mb
25.1
ELECTRONIC
AIR
SHUTTER
OPENING
ORIFICE
33.1
W415-2835 / A / 12.09.20
1/2"
EN
(9
La flam
la son
3/8" - 1/2"
(9.5
3/8" à 1/2"
(9.5
L
e
the
3/8" - 1/2"
d
(9.5
thermopile
(9.5
La flamme
la thermoc
3/8" - 1/2"
(9.5mm
1/2"
59