Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
General Information
Unpack the fire carefully and retain the packaging for possible future use, in the event of moving or returning the fire to
your supplier. The Remote Control and batteries are packed separately in the carton.
The fire incorporates a flame effect, which can be used with or without heating, so that the comforting effect may be
enjoyed at any time of the year. Using the flame effect on its own only requires little electricity.
Before connecting the fire check that the supply voltage is the same as that stated on the fire.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is
related to the operation of the flame effect. This is normal and should not be a cause for concern.
Electrical connection.
WARNING – THIS APPLIANCE MUST BE EARTHED.
This fire must be used on an AC ~ supply only and the voltage marked on the fire must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating instructions.
PLEASE RETAIN THIS USER'S GUIDE FOR FUTURE REFERENCE
Do not put plastic components into a dishwasher.
Only slide out the drawer when the water tank needs to be filled or a lamp needs to be changed otherwise you
will inadvertently alter the water level and the flame effect operation.
Only use filtered tap water in this appliance.
Always ensure that the fire is sitting on a level floor.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and
dry the sump.
Once installed, never move this fire or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air filters must be cleaned once every two weeks, particularly in
hard water areas.
The fire appliance should never be operated if the lamps are not working.
The lamps should be regularly inspected as described under 'Maintenance' and 'Changing lamps'.
Technical Information
Model No: ABN 15 E
Heat Output
Nominal Heat Output
Minimum Heat Output
Maximum Continuous Heat Output
Auxiliary Electricity Consumption
In Standby Mode
electronic room temperature control plus week timer
Installation Instructions
Ensure that all packing items are removed (read any warning labels carefully).
Retain all packing for possible future use, in the event of moving or returning the appliance to your supplier.
To install the appliance;
Hold the fire by the sides of surround and gently manoeuvre into position. Plug the fire into a 13amp/240 volt outlet.
Ensure that the supply cable exits at the front of the fire, at the right or left hand corner to suit your supply socket location
and is not trapped under the fire such that it might cause it to be damaged.
Before switching on the appliance, please read the following instructions.
Replacement of drawer cover.
If the drawer cover is to be replaced, please use a sutibaly shaped and sized piece of material used to create the fire
surround. We advise to use 4 x M6 nut inserts in the new front panel and fix in the same way as the current panel.
Ensure that there is a 10mm gap between the hearth of the fire place and base of the tray drawer cover.
Replace the drawer cover using the following steps;
1. Open the drawer fully, lift the tank and sump out of the appliance and carefully place aside.
2. Remove the 4 screws as shown in Fig.19 removing the drawer cover and metal mounting plate.
3. Remove the 4 M6 screws releasing the drawer cover from the metal mounting plate.
4. Using the suitably shaped and sized piece of material with the M6 nut inserts in place (please use current panel as a
guide) screw the new drawer cover to the metal mounting plate with the M4 screws.
5. Replace the drawer cover and metal mounting plate by reversing steps 1 and 2
Before using the manual controls firstly fill the water tank (See 'Maintenance', 'Filling the water tank').
230V
P
1,4
Nom
P
0,7
min
P
1,4
max
P
0,8
Nom
31
240V
1.5
kW
0,8
kW
1.5
kW
0,97
kW
Publicité
Table des Matières
