Startup; Operating Instructions; Suggested Maintenance; Filter Replacement - Watts Pure H2O Manuel D'installation, D'utilisation Et D'entretien

Start Up
Step 1 – Make sure the valve on the lid is turned to "FLOW".
Step 2 – Open a faucet downstream of the Whole House filter unit.
Step 3 – Slowly turn on main water supply until faucet downstream
is steadily flowing.
Step 4 – Turn off faucet and check for leaks at your connections.
Monitor for leaks for 24 hours after installation.

Operating Instructions

This whole-house filter features a Valve-In-Head design. This
allows you to control water flow through the unit without
additional hardware.
(SEE LABEL FOR POSITION)
VALVE OPERATION
BY-PASS Allows water to continue to flow through the house NOT utilizing the filter.
OFF Shuts off water before the filter.
FLOW Allows water through the house utilizing the filter.
Note: In all three modes the unit will remain under pressure.

Suggested Maintenance

This whole house filter can use 5, 10, 20, or 50 micron sediment
filters. This kit includes three (3) 50 micron filters. The recommended
filter is a 50 micron. The recommended time for replacing your filter
is every three (3) to six (6) months depending on your incoming
water conditions. If your water contains more sediment you may be
required to change your filters more often. Failure to change filters
regularly will reduce water pressure & flow. Periodically check filter
for sediment or dirt loading.

Troubleshooting

PROBLEM
1. Filter bowl has no water in it
2. Leaking at the bowl
3. Leaking at the valve fittings
4. Leaking at top of valve (lid)
5. Low water flow / pressure
CAUSE
Water is not turned on at Main
Valve turned to "BY-PASS" or "OFF"
O-Ring kinked or not seated
Bowl not tightened enough
Improper installation / Not enough plumber's tape on fitting
Faulty lid
Filter clogged

Filter Replacement

Step 1 – Shut off the water to the filter housing by turning the
bypass valve to "BYPASS" or "OFF".
Step 2 – The bowl of the system can be removed by turning it
clockwise (see Figure 1). Use the supplied filter wrench to
loosen the housing.
Step 3 – Remove the old filter and discard.
Step 4 – Clean the filter housing with a mild soap solution and
rinse with water. Check O-ring and lubricate with water
soluble lubricant.
NOTICE
Petroleum based lubricants (such as Vaseline®) must not
be used.
Step 5 – Replace filter.
Step 6 – Reinstall by turning the filter bowl counter-clockwise (see
Figure 1) onto the lid. Make sure O-ring is properly seated.
NOTICE
Hand tighten housing. Wrench should only be used to
loosen housing.
Step 7 – Turn bypass valve back to "FLOW".
Step 8 – Check for leaks. Monitor unit for leaks for 24 hours after
filter replacement.

Product Registration

To register your product, please visit www.watts.com/pureh2o and
select "Register Now". Watts Pure H2O is concerned for the safety
of your personal information. Watts Pure H2O collects personal
information when you register with Watts Pure H2O. This information
is stored in our data base and we do not rent, sell, or share personal
information with other people or nonaffiliated companies.
We reserve the right to send you certain types of communications
such as direct mail, email, or by telephone relating to our products
or products that you have purchased. We limit access to your per-
sonal information to those employees who will directly provide you
with services or products in order to do their jobs.
Check that the water is on at Main
Make sure valve is turned to the "FLOW" position
Check / Replace / Re-seat O-Ring
Tighten bowl
Replace or repair fittings
Call Watts Pure H2O at 1-978-689-6066 for a replacement
Replace filter
3
SOLUTION