Black & Decker BDL100AV Mode D'emploi page 2

• To remove the temporary wall mounting
suction cup, pull the rubber release tab (J)
straight out as shown in figure 3.
CAUTION: Pin is sharp and should be
USING THE PIN (OPTIONAL)
handled with care.
• Insert pin straight and seat firmly against
surface as shown in figure 4. The pin should
always be pushed in by hand and never
driven by a hammer.
• To remove pin from the wall, pull straight
out.
CAUTION: Always store pin as shown in
figure 5 when not in use.
LASER LEVEL FUNCTION
• Connect the laser level to the wall
attachment as shown in figure 6.
Wall attachment has a strong magnet (H) that
attracts to metal plates (K) located under the
label on both sides of the laser allowing for
easy up and down adjustment for about ¾ of
an inch (19 mm).
NOTE: Laser can be flipped to project a
horizontal laser line in either direction.
• Move on / off switch actuator (C) to position
"1" to activate the color change on the bubble
vial. - figure 7.
• Move on / off switch actuator (C) to position
"0" to turn off the laser.
• Move on / off switch actuator (C) to position
"2" to project the laser line and activate the
color change on the bubble vial.
DANGER: Laser Radiation, avoid direct
eye exposure.
AUDIO VISUAL LEVEL FUNCTION
• If the device is not level, the bubble vial will
be "RED".
• To level the device, rotate it in either
direction until the bubble vial turns "GREEN".
• Figure 9 depicts using the laser to hang several pictures in a straight line.
9
3
4
5
6
K
H
7
1
0
2
8
• There is also an audio button (D) which can be used to signal when an item is level that is
out of sight as shown in figure 10.
• To use the audio leveling feature, turn the device on by moving the switch (C) to position "2"
shown in figure 7.
• Push in on the audio On/Off button (D). The device will begin to "beep" on and off.
• Place the device on top of the item that you are leveling.
• Begin leveling. The beeping speed will increase when the item is near level. When the item
is leveled the signal will become continuous and stop.
• If you have gone past level the beeping tone will noticeably change.
10
BEEP, BEEP,
BEEP, BEEP, BEEP
BEEEEEEEEEEEEEEP
• The laser line is only level on the wall against which the unit is held or hung. The short line
Helpful Hints
visible on any adjacent wall is not level. The same is true for straight line projection on a
floor or wall, the short line on any adjacent wall is not level.
• The laser unit only generates a level line when held or hung against a vertical surface.
• Make sure laser is as square as possible to flat surface to ensure proper line projection.
Always store the laser level indoors.
Storage
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
Maintenance
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized service
centers or other qualified service organizations, always using identical replacement parts.
WARNING:
Accessories
The use of any accessory not recommended for use with this tool could be
hazardous.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days after
the sale). Proof of purchase may be required. Please check with the retailer for their specific
C return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province. Should
you have any questions, contact the manager of your nearest Black & Decker Service
Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained in the
packaging, call the local company or see the website for warranty information.
TECHNICAL SPECIFICATIONS OF LASER LEVEL:
Laser diode wavelength: 633 - 670 nm (red color)
Laser Class: Class IIa
Working range: Up to 15 feet (depends on light conditions)
Leveling accuracy:
Projecting Horizontal ±1/4 inch (6 mm) @ 10 feet (3 m)
Batteries: 2 AAA (included)
Voltage: 3 Volts
Operating temperature: 50°F (10°C)- 104° F (40°C)
Problem Possible Cause
• Unit does not work. • Weak batteries.
• Level blinking red. • Weak batteries.
• No audio signal. • Audio button not pushed.
• Level blinking randomly • Restart software.
with different colors.
• Suction cup will not hold • Wall surface too porous.
on wall.
• No laser line • Switch in wrong position.
• Level wonʼt stay steady • Out of height adjustment range.
when on wall mount.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
Troubleshooting
Possible Solution
• Replace if needed.
• Replace batteries.
• Push audio button.
• Turn unit OFF and after 5
seconds turn unit ON.
• Try another location or use
push pin.
• Move switch to lowest
position.
•Readjust height position of
suction cup).
See 'Tools-
– Yellow Pages –
for Service &
Electric'
Sales