Atel MIKE Instructions De Montage page 4

Pag. 4 di 12
VISITOR CALLING
1 - The visitor presses the CALL button on the camera
2 - The visitor shape appear on the Monitor screen
3 - Hold up the handset and talk with the visitor
4 - After conversation, return the handset on original place.
- If a visitor presses the CALL button of the camera, a chime sounds and the visitor appears
on the monitor screen automatically.
- After viewing the visitor, pick up the handset and talk with him as you use regular
telephone (When you talk with the visitor with holding the handset, the scene of monitor
is off automatically after about 2 minutes)
- When you return the handset on original place after conversation, operation is completed.
In case of permitting the visitor's entrance, press DOOR RELEASE button of monitor, and
the door will be opened automatically.
MONITOR OPERATION
1 - Press the MONITOR button without holding up the handset
2 - Image will appear and least for 2 seconds.
WHEN YOU WANT TO USE IMAGE AND SOUND
When you hold up the handset, you can check the outdoor situation.
In case of using the handset, you can also talk with outdoor speaker.
WHEN YOU WANT TO USE ONLY IMAGE
Though you don't want hold up the handset, you can view outdoor pressing MONITOR
button. At this time, you can not talk with outdoor speaker.
HOW TO SOLVE PROBLEMS
Problem: The set doesn' t operate
Check:
- The power supply cable is not properly inserted in the AC outlet, or the AC is not supplied.
- Wires between MONITOR and CAMERA are shorted, disconnected or misplaced in
polarity connections.
- Set's wires must stay in distance from other cables.
Problem: Image is not clear enough
Check:
- Has been CONTRAST control properly adjusted?
- Are the MONITOR screen and CAMERA lens clean?
Problem: Interphone does not work
Check:
- Is the handset cord disconnected from the monitor?
Periodically clean the set with a dry cluster.
Don't use chemical products like benzene to execute the cleaning
TECHNICAL CARACTERISTICS
Power supply:
Power Consumption:
Working Temperature:
Communication System:
Call Signal Sound:
Conversation Time:
Wiring:
Max Wiring Distance:
Scanning Frequency:
Dimensions:
Weight:
Power supply:
Power Consumption:
Working Temperature:
Image Sensor:
Image angle:
Minimum Illumination:
Illumination:
Dimensions:
Weight:
MAINTENANCE
MONITOR
12Vdc/0,85A (with external supplier)
85÷260Vac (with internal supplier)
10W if active - 0,5W on stand-by
0÷40°C
Duplex Handset Conversation
Flips on at the 2 nd Chime
Auto-off in 2 minutes
4 wired in polarity (Voice, Picture, Power, GND)
4x0,65mm 2 =50m, Coaxial Cable 5C-2V=80m
Horizontal=15,73KHz - Vertical=60Hz
196x228x50mm
1.130g
CAMERA
12Vdc - 0,25A (Monitor power supply)
3W if activated
-10 ÷ +50°C
1/3" CCD, 310,000 pixels
Horizontal=71° - Vertical=53°
0,1 Lux at about 30 cm in distance
Infrared LED
120x184x22mm
210g
SPECIAL FEATURES
1 - Excellent door vision: This door VISION is a visual intercom system with a 4" CRT built
in monitor and a separate outdoor camera unit.
2 - Simple and easy installation: This unit has 4 polarized wires. You can use the wires of
an existing doorbell or intercom as they are without without additional wiring.
3 - Clear scene quality: You can correctly identify visitor with clear scene quality by up-to
date CCD camera and the 4" flat CRT.
4 - Night identification: 6 infrared LEDs on camera unit allows you to identify visitor even in
poorly lit areas or at night without any light source.
5 - Burglar Alarm: To protect against stealing, indoor monitor speaker emits an emergency
alarm in case of camera breackdown or wires disconnection.
6 - Adjustable Lens Angle: Lens angle can be adjusted at user's convenience within limit of
about 15° degrees each up and down from horizontal position.
7 - Door Release Function: Adding an optional electric door release, you can open door
from monitor without going to the porch.
8 - Two-way Intercom: This system permits two-way intercom between the indoor monitor
and the outdoor camera.
9 - Automatic Visitor Identification: When a visitor presses the CALL button on camera unit,
the indoor monitor is automatically activated. If necessary, you can control the camera
area without talk.
!! IMPORTANT !!
SAVE THESE INSTRUCTIONS
1° - Keep your videophone away from strong magnetic force such as TV or
video (It has risk of affecting screen image badly).
2° - Set's wires must stay in distance from other cables.
3° - Do not spill water directly onto the videophone (It causes trouble to the
videophone).
4° - Keep the videophone from any physical shock (It causes disorder or
damage).
5° - Don't install the videophone in direct sun light or strong reflected rays.
6° - Plug out the adaptor from the wall outlet in case of no use for a long time.
7° - Don't connect many lines to one plug as shown on this drawing (It may
cause fire or disorder).
8° - Don't install the videophone near the ammonia, acid materials and
poisonous gas (It causes disorder).
9° - High voltage flows inside the system. Don't disassemble the unit carelessly
(It causes disorder or electric shock).
ATEL ACCEPTS IS NOT LIABLE for any damage caused by the not abiding of
the safety regulations and laws at present in force not being observed during
installation.