Gima 2246A Manuel D'utilisation page 10

1 ABOUT THIS MANUAL
This manual shall only be used for the reference of operation of this particular model. If the manual is used for other purposes, we will not under-
take any according consequences and responsibility.
All information of this manual shall be protected by copyright and shall not be copied and translated in any part of this specification without the
written consent of manufacturer.
2 WARNING
• Power supply must be cut off when changing electrical components or maintaining and cleaning machines.
• The plug must be plugged into an outlet that is properly installed and grounded, to prevent the risk of fire and electric shock.
• Do not stand on this equipment.
• Do not allow children to play with and place the equipment in a place where children can touch. Please adjust the backrest to the highest position
when you leave.
• Please do not place the equipment in wet places such as bathroom to avoid electric shock or other failure; Also keep the controllers away from
water.
• Please do not place and operate the equipment in places where is painting/coating or supplying oxygen.
• Unless being monitored or instructed by personnel who can be responsible for their personal safety, the people who have physical obstacles,
tactile disorders, mental disorders, lack of experience, common sense or children, are not allowed to use the equipment.
• Please contact distributor, service center or related personal with appropriate skill and experience for repairing if the plug is damaged, in case
of any danger.
• Please make sure there is no accessible thing within the stroke during any operation of the beds.
• Operation should be processed by trained professionals.
3 PRECAUTIONS
• The equipment should be used by an experienced person who must be familiar with the product structure, performance and instructions. And
make the regular maintenance work.
• Read this manual carefully before installation, operation and adjustment. And please keep it well.
• This product shall not be used for single side or single point loading work.
• Comply with safety operation rules, do not overload the use of products, to ensure that the product safety protection equipment is complete and
reliable, eliminates unsafe factors on time.
• Tighten bolts and nuts regularly to avoid failure caused by loose, sliding, vibration and falling parts.
• During the maintenance, the operator shall not disassemble any parts of the bed at will.
• This product is not allowed to operate when it's with fault. If abnormal phenomenon or abnormal sound is found, it must be stopped for inspection
immediately, and work can be resumed after troubleshooting.
• The operator must be familiar with the precautions described in each section of the manual to
ensure the safety of person and product.
• This electric beauty bed is equipped with a three-wire power cord. The power cord must be
plugged into a three-hole outlet which is properly installed and grounded. This is not only to
prevent the risk of electric shock, but also ensure bed work properly.
• Please operate the equipment strict accordance with the warning label pasted to the prod-
ucts.
• While controlling the lifting of the whole bed, the button must be pressed continuously until the
bed in a suitable position.
• Please pay attention that the continuous working times should be Max. 2Min. ON ; 18Min.
OFF, when operating the motor.
• Maintenance should be processed by trained professionals.
• After each treatment, please use neutral reagent to clear the dust, stains on leather or on
wood pieces.
• When adjusting the backrest, seat cushion, footrest or lifting of the whole bed by hand control-
ler or installed foot controller, please keep your hands, feet and head away from the position.
(Please see right picture)
4 APPLICABLE RANGE
These electric beauty beds are suitable for beauty, massage and manicure treatment.
5 INSTALLATION
1. Put the bed to a proper location, according to the overall layout, the daylighting or artificial lightings and operation condition of the salon's or the
home. And keep it in the clean, dry and cool environment.
2. Open the packing carton to check if the bed is intact and whether the accessories or spares are complete. Please contact distributor or us if
there's any problem.
3. Installation
Place the bed to the proper position. Please note that it is unnecessary to install extra screw on the floor to fasten the bed, because the original
design has taken the stability performance into consideration. But please ensure the bed is placed on a firm and flat ground, so as to prevent
any accident. If the bed rotates or slant due to rough ground, please adjust the four pieces rubber feet (M10x30) and nuts (M10) fasten on the
chassis by hexagon open-end wrench, so as to ensure the bed is stable.
4. Power supply and controllers connections:
Connect the power supply, hand controller, and foot controller to the bed. Voltage and
frequency input shall be 110-120V/60Hz , 220-240V/50Hz.
Input ports: INPUT (for power supply), HAND CONTROLLER, FOOT CONTROLLER.
(as shown in the right picture)
5. Connect the plug with power supply properly. (Details as shown below)
ENGLISH
10