Using The Rangetop - hestan KRT Manuel D'utilisation Et D'entretien

USING THE RANGETOP

BURNER CONTROL KNOBS BURNER CONTROL KNOBS
Each sealed burner has its own control knob. The symbol
below each knob indicates which burner is controlled by each
EN
knob. Push and turn LEFT (counter-clockwise) to HI to ignite
the flame, then turn to the desired flame setting.
SMART BURNER SMART BURNER
The Smart Burner
communicates with Hestan Cue cookware via
wireless technology. This feature provides a unique
thermostatic control of the heating, as well as traditional
manual heat control for Cue and non-Cue pans. Please read the
Smart Burner
BURNER TYPES & OUTPUT BURNER TYPES & OUTPUT
This table indicates the type and
output of each sealed burner.
Dual-flow burners have an inner
and outer row of ports, with a
simmer function. The single-flow
burner (some models) is similar to
a commercial burner and features
very high output, and a low, but no
simmer function.
RE-IGNITION RE-IGNITION
Each sealed burner has its own electronic spark-ignition module with flame-sensing technology and
automatic re-ignition capability. If any burner should blow out, the igniter automatically re-lights the
burner.
Each burner should light in less than 4 seconds. Once lit, the sparking will stop. On very low simmer,
an occasional sparking may occur. This is usually due to a breeze in the room. If an igniter continues to
spark even with a flame present, there could be an electrical wiring issue, or some other problem. See the
TROUBLESHOOTING section of this manual for more information.
Note: The Smart Burner
gas will flow during this self check process. Sparking should not exceed 4 seconds.
DO NOT touch the burner or the igniters while sparking is occuring. A shock hazard or burns could occur.
MANUAL LIGHTING / POWER FAILURE MANUAL LIGHTING / POWER FAILURE
THE GRIDDLE AND SMART BURNER
Each sealed burner can be manually lit in the event of a power failure. It is necessary to light each burner
individually.
If a power failure occurs WHILE you are using the sealed burners, turn all the knobs to the OFF position -
then light manually with a match or fireplace lighter.
Position the match or fireplace lighter at the port nearest the igniter, then turn the knob to HI until the
flame is lit. Wait until the flame has lit all the way around the burner before adjusting the knob to LOW
or SIMMER.
IF YOU SMELL GAS, turn all control knobs to OFF - check the precautions listed in the SAFETY section
of this manual.
14
©2021 Hestan Commercial Corporation
CONTROL KNOB CONTROL KNOB
TM TM
features a special control knob which
TM
TM section of this manual for more information.
may take longer to light as the system runs a self check prior to ignition. No
TM
TM
®
Bluetooth
BURNER OUTPUT - NATURAL GAS
DUAL-FLOW OUTPUT DUAL-FLOW
(FRONT) (BTU/hr) (REAR)
HI 23000
4200
LOW
1500
SIMMER HI SIMMER HI
SIMMER LOW 500 SIMMER LOW
BURNER OUTPUT - PROPANE
DUAL-FLOW OUTPUT DUAL-FLOW
(FRONT) (BTU/hr) (REAR)
HI 23000
LOW 4200
1500
SIMMER HI SIMMER HI
600
SIMMER LOW SIMMER LOW
CANNOT BE USED DURING A POWER FAILURE.
OUTPUT SINGLE
(BTU/hr) FLOW
HI 15500 MAX
4200
LOW LOW
1500
SMART
BURNER
500 GRIDDLE
OUTPUT SINGLE
(BTU/hr) FLOW
HI 15500 MAX
LOW 4200
LOW
1500 SMART
BURNER
600 GRIDDLE
OUTPUT
(BTU/hr)
30000
4200
20000
TM
15000
OUTPUT
(BTU/hr)
22000
4200
20000
TM
15000