Lubrication; Technical Data - Chicago Pneumatic CP7215 Serie Manuel De L'opérateur

EN
English
INSTRUCTION MANUAL
Machine Type
Power tool equipped with a flexible disc fitted with abrasive
paper for sanding - No other use is permitted
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes
shown in the diagram below.
3. Do not install a quick coupler directly into the sander
throttle handle.
1/4"NPT
3/8" (10mm)

Lubrication

Use an air line lubricator with SAE #10 oil, adjusted to two
drops per minute. If an air line lubricator cannot be used,
add air motor oil to the inlet once a day.
Maintenance
1. Disassemble and inspect air motor and orbital assembly
every three months if the tool is used every day. Replace
damaged or worn parts.
2. High wear parts are underlined in the parts list.
3. To keep downtime to a minimum, the following service kits
are recommended:
Tune-Up Kit
8940163459 (Incl: 7, 17, 19, 20, 23, 26, 33, 50)
ECO Change Motor Kits
(Incl: 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26,
27, 29, 30, 33, 34, 50)
ECO Change Motor
CP7215: 8940168374
CP7225: 8940168372
CP7255: 8940168373
Throttle Kit CP72 Series
8940168367 (Incl: 2, 3, 4, 5, 6)
Valve Seat Kit CP72 Series
8940168368 (Incl: 7, 8, 9)

Technical Data

Pad Diameter 6in. (150mm)
Free speed 12,000 RPM
Air pressure 90 psi (6.3 bar)
Spindle size 5/16"-24
Original Instructions
Copyright 2010, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents
or part thereof is prohibited. This applies in particular to trademarks,
model denominations, part numbers and drawings. Use only
authorized parts. Any damage or malfunction caused by the use of
unauthorized parts is not covered by Warranty or Product Liability.
1/2" (12mm)
REGULATOR
90
0 130
1/2" (12mm)
FILTER
LUBRICATOR
CP7215, CP7225 & CP7255 Series
Noise & Vibration Declaration
Sound pressure level 81 dB(A), uncertainty 3 dB(A), in
accordance with EN ISO 15744. For sound power, add 11
dB(A).
Vibration value;
CP7225, CP7225E, CP7225SV, CP7225SVE, CP7225CV,
CP7225CVE: a< 2.5m/s
2
CP7255, CP7255SV, CP7255CV: a= 4.1m/s
2.4m/s
2
CP7255E, CP7255SVE, CP7255CVE: a= 3.3m/s
k= 1.6m/s
2
CP7215, CP7215E, CP7215SV, CP7215SVE, CP7215CV,
CP7215CVE: a= 4.9m/s
2
28927-3.
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the
latest information please visit cp.com.
These declared values were obtained by laboratory type testing
in accordance with the stated standards and are suitable for
comparison with the declared values of other tools tested in
accordance with the same standards. These declared values are
not adequate for use in risk assessments and values measured in
individual work places may be higher. The actual exposure values
and risk of harm experienced by an individual user are unique
and depend upon the way the user works, the workpiece and
the workstation design, as well upon the exposure time and the
physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of values
reflecting the actual exposure, in an individual risk assessment in a
work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is
not adequately managed. An EU guide to managing hand-arm
vibration can be found at http://www.humanvibration.com/EU/
VIBGUIDE.htm
We recommend a programme of health surveillance to detect early
symptoms which may relate to noise or vibration exposure, so that
management procedures can be modified to help prevent future
impairment.
MANUFACTURER'S LIMITED WARRANTY
Limited Warranty: The "Products" of the Chicago Pneumatic Tool
Co. LLC ("CP") are warranted to be free from defects in material and
workmanship for one year from the date of purchase. This Warranty
applies only to Products purchased new from CP or its authorized dealers.
Of course, this Warranty does not apply to products which have been
abused, misused, modified, or repaired by someone other than CP or its
Authorized Service Representatives. If a CP Product proves defective in
material or workmanship within one year after purchase, return it to any
CP Factory Service Center or Authorized Service Center for CP tools,
transportation prepaid, enclosing your name and address, adequate
proof of date of purchase, and a short description of the defect. CP will,
at its option, repair or replace defective Products free of charge. Repairs
or replacements are warranted as described above for the remainder of
the original warranty period. CP's sole liability and your exclusive remedy
under this Warranty is limited to repair or replacement of the defective
Product. (There Are No Other Warranties Expressed Or Implied And
CP Shall Not Be Liable For Incidental, Consequential, Or Special
Damages, Or Any Other Damages, Costs Or Expenses Excepting
Only The Cost Or Expense Of Repair Or Replacement As Described
Above.)
6" Random Orbital Sander
, uncertainty k=
2
2
, uncertainty k= 3.4m/s re. ISO
2
, uncertainty