Replacement Parts And Accessories - Flexzilla L1388LFZ Instructions D'utilisation

• Make sure power cord circuit voltage is the same as that shown on the charger. Connect charger to the power source.
• Place small plug on the end of the charger cord into the plug hole on the back of the battery. Do not force. When proper connection is
made, the red light will glow, indicating the charger has switched to quick-charge mode.
• Charge the battery for one full hour including quick-charge time prior to initial use.
• When the battery pack is fully charged, the red light will go out and the green light will glow. The battery pack will continue to receive a
trickle charge. Remove the battery pack from the charger.
• Disconnect charger power cord from the power source when not charging battery pack.
• Important: Battery pack temperature will increase during and shortly after use. The battery pack may not accept a full charge if
charged immediately after use. For best results, allow the battery pack to cool to room temperature before charging.
GREASE GUN OPERATION:
• Insert fully-charged battery pack into the end of the grease gun handle by aligning the slots in the handle with the matching boss on
the battery pack. Do not force objects. Make certain battery pack is fully engaged into handle cavity and snaps into place at battery pack
latch button. Depress tool switch momentarily to check battery pack connection to tool. To release battery from tool handle, depress
battery pack latch button until battery releases and can be withdrawn from cavity in tool handle. Do not allow metal objects to contact
battery pack terminals while battery is not in charger or tool.
• Re-Priming: Follow procedure for cartridge loading (see "Assembly" section), but do not reload. This procedure will allow the gun to
reprime using the automatic bleeder valve. If necessary, repeat the process until all trapped air pockets have been purged from the
grease barrel.
• Connect grease coupler to standard grease zerk fitting on equipment or machinery to be greased. Release trigger to stop grease flow.
To disconnect grease coupler from zerk, angle the coupler and use a twisting motion. If the coupler will not disengage, the tip sleeve of
the coupler can be loosened with tools to allow adjustment in the tension of the coupler gripping the grease zerk fitting. Retighten the
coupler sleeve to prevent coupler leaking.
• Operate the trigger to dispense grease. The trigger must be continuously depressed to dispense grease. If back pressure in the grease
line exceeds the 7000 psi limit, grease will then be expelled from the pressure relief valve to limit the pressure in order to reduce risk of
motor overload and limit excessive grease pressure in grease hose. Do not exceed specifications or alter gun to perform beyond ratings.
Such misuse will void the warranty and can result in possible injury.
• WARNING: To reduce the risk of personal injury, always unplug the charger and remove the battery pack from the charger or tool
before performing any maintenance. Never disassemble the tool, battery pack, or charger. Refer to an authorized service facility for all
repairs.
• WARNING: To reduce the risk of personal injury and damage, never immerse your tool, battery pack, or charger in liquid or allow a
liquid to flow inside them or be splashed on them.
• Maintaining tool:
a. If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the
tool still does not work properly, contact an authorized service facility for assistance.
b. Clean excessive grease buildup from tool exterior. To reduce the risk of injury and damage, wipe grease from tool exterior
surfaces. It may become difficult to operate the tool and handle in a safe manner if tool surfaces become grease covered.
Disconnect charger from power source and allow to cool before cleaning. Wipe surfaces with dry towel to remove grease. Do
not use water or any cleaning solvents on tool, charger or battery pack.
c. Inspect grease hose for damage, excessive bending, cracks, and cuts. Do not use damaged or worn hoses. Replace worn or
damaged hoses immediately. Use only replacement hoses that are marked and designed for the pressures this tool can develop.
Do not use any defective, unmarked, or damaged hoses. Do not repair the grease hose. Replace if damaged.
d. Replace worn or damaged grease fittings. Replacement fittings must be capable of withstanding the pressures developed.
• Flexzilla Replacement 42 in. Grease Hose ............................................................................. L2930FZSP
• 20V DC Lithium-Ion Battery Pack ........................................................................................... L1388LFZ-B
• 1-Hour Quick Charger............................................................................................................. L1388LFZ-C
• Optional Universal Filler Nipple (for use with manual grease transfer pumps) ....................... L2461
• Optional grease cartridge storage box.................................................................................... GCB12
(Rigid polypropylene container for storing and transporting twelve standard 14 oz grease cartridges, shoulder strap included)
WARRANTY* LEGACY MANUFACTURING COMPANY ("LEGACY") warrants that this equipment will be free from defects in material
and workmanship for a period of one (1) year from the date of purchase, under normal use. LEGACY'S sole obligation under this
warranty is limited to replacing or repairing, free of charge, any equipment that proves to be defective under normal conditions and use
according to the recommendations of LEGACY. To obtain repair or replacement, the equipment must be shipped to a LEGACY
authorized Warranty and Service Center during the warranty period, transportation charges prepaid, with proof of date of purchase. In
the event of repair or replacement, the warranty period shall not be extended beyond the original warranty period. While necessary
maintenance or repairs on your Legacy equipment can be performed by any company, we recommend that you use only authorized
Legacy service centers. Improper or incorrectly performed maintenance or repair voids this warranty. Contact us at
service@legacymfg.com or www.legacymfg.com for ordering or installation instructions.
Maintenance

Replacement Parts and Accessories

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USE.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.