Maintenance And Service; Maintenance And Cleaning; Français; Consignes De Sécurité - Bosch EasyCut 50 Notice Originale

openings in the base plate (3). from the left or right. Lock it
using the locking lever (23).
The guide rail must not protrude over the edge of the
workpiece being sawn into.
Put the saw with the guide rail adapter (22) fitted on the
guide rail (24). Switch on the power tool and push it gently
in the cutting direction, guiding it evenly.
Mitre/bevel cuts up to 45° can be produced using the short
side of the Bosch (2 609 255 732) plastic guide rail.
Plunge cutting (see figure G)
Plunge cuts may only be applied to wood.
u
Plunge cutting is possible only with a mitre/bevel angle of 0°.
Place the power tool so that the rear edge of the base
plate (3) rests on the workpiece, without the saw blade (8)
touching the workpiece, and switch it on. When using power
tools with speed control, select the maximum speed. Press
the power tool firmly against the workpiece and allow the
saw blade to plunge slowly into the workpiece.
As soon as the base plate (3) rests fully on the workpiece,
continue sawing forwards along the required cutting line.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Always clean the saw blade and saw blade receptacle
u
dry. Use a fine brush (see figure H) to remove more
deeply ingrained dirt.
The saw blade is maintenance-free. The chain of the saw
blade does not need to be oiled.
Clean the saw blade receptacle (16) regularly. To do this,
remove the saw blade from the power tool and gently tap out
the power tool on a flat surface.
If the power tool becomes very dirty, this can lead to serious
faults. For this reason, do not cut materials which generate
large quantities of dust from below or overhead.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
Bosch Power Tools
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment and its implementation
into national law, power tools that are no longer usable must
be collected separately and disposed of in an environment-
ally friendly manner.
Français
Consignes de sécurité
Avertissements de sécurité généraux pour l'outil
électrique
Lire tous les avertissements de sé-
AVERTISSE-
curité, les instructions, les illustra-
MENT
tions et les spécifications fournis
avec cet outil électrique. Ne pas suivre les instructions
énumérées ci-dessous peut provoquer un choc électrique,
un incendie et/ou une blessure sérieuse.
Conserver tous les avertissements et toutes les instruc-
tions pour pouvoir s'y reporter ultérieurement.
Le terme "outil électrique" dans les avertissements fait réfé-
rence à votre outil électrique alimenté par le secteur (avec
cordon d'alimentation) ou votre outil électrique fonctionnant
sur batterie (sans cordon d'alimentation).
Français | 17
1 609 92A 65Z | (25.11.2020)