Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
finished talking, he said "Roger" in order to prevent his correspondent that
it was his turn to talk. The word "Roger" has been replaced by a significant
beep. There comes "Roger beep" from.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
the RG BP function.
to
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
activate
deactivate
to
On /
Of the function.
4.
New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to
adjust
another function or b) Press the PTT switch (17)
to
validate
and
exit
MENU.
5.
If no key is pressed, the unit
exits
the display.
Default ROGER BEEP is Of.
4) TONE
The TONE function is used to
change
-5 to +5.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the TONE function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
a new value.
4.
New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to
adjust
another function or b) Press the PTT switch (17)
validate
exit
MENU.
to
and
5.
If no key is pressed, the unit
exits
the display.
Default TONE is 0.
5) DIMMER
The DIMMER function allows to
backlight or to set no backlight (OF).
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the DIMMER function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
a new value.
enter
MENU.
is displayed.
The current status blinks on display.
disappears.
MENU after 10 seconds,
disappears on
the tone on reception. 11 levels from
enter
MENU.
is displayed.
The value of the tone blinks on display.
disappears.
MENU after 10 seconds,
disappears on
adjust
the brightness (from 1 to 9) of the
enter
MENU.
is displayed.
The value of the dimmer blinks on display.
4.
New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to
adjust
to
validate
and
exit
MENU.
5.
If no key is pressed, the unit
the display.
Default DIMMER value is 9.
6) EMG SET 1
set
Allows to
the Priority Channel 1.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
the EMG 1 function.
to
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the channel.
4.
New press on PUSH knob (6) to validate. The second parameter, the band
blinks.
5.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the frequency band in segments:
BAND NAME page 27).
6.
New press on PUSH knob (6) to validate. The third parameter, the mode
blinks.
7.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the mode.
8.
New press on PUSH knob (6) to validate. a) Go back to point 1 to
another function or b) Press the PTT switch (17) to
disappears.
9.
If no key is pressed, the unit
the display.
Default Priority channel 1 is channel 9/AM/band A.
See § PRIORITY CHANNELS page 24.
7) EMG SET 2
Allows to set the Priority Channel 2.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the EMG 2 function.
Points 2 to 9 are identical to § EMG SET 1.
Default Priority channel 2 is channel 19/AM/Band A.
See § PRIORITY CHANNELS page 24.
26
another function or b) Press the PTT switch (17)
disappears.
exits
MENU after 10 seconds,
disappears on
enter
MENU.
is displayed.
The channel blinks on display.
validate
and
exits
MENU after 10 seconds,
disappears on
enter
MENU.
is displayed.
(see
adjust
exit
MENU.
Publicité
Table des Matières
