Compliance Information - dji FPV Guide De Démarrage Rapide

Compliance Information

FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its
highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model
is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure
limit established by the FCC, Tests for each product are performed in positions and locations as required by the FCC.
For Handheld operation, this device has been tested and meets the FCC RF exposure guidelines when used with an
accessory designated for this product or when used with an acces sory that contains no metal.
For body worn operation, this Remote Controller (Model: P1RC) has been tested and meets the FCC RF exposure
guidelines when used with an accessory designated for this product.Non‐compliance with the above restrictions may
result in violation of RF exposure guidelines.
ISED Warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may
not cause interference.(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes :(1)L'appareil ne doit pas produire de brouillage; (2)L'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
SAR tests are conducted using standard operating positions accepted by the ISED with the device transmitting at its
highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model
is a available for sale to the public, it must be tested and certified to the ISED that it does not exceed the exposure
limit established by the ISED, Tests for each product are performed in positions and locations as required by the ISED.
For Handheld operation, this device has been tested and meets the ISED RF exposure guidelines when used with an
accessory designated for this product or when used with an acces sory that contains no metal.
For body worn operation, this Remote Controller (Model: P1RC) has been tested and meets the ISED RF exposure
guidelines when used with an accessory designated for this product.Non‐compliance with the above restrictions may
result in violation of RF exposure guidelines.
Les essais SAR sont effectués à l'aide de positions de fonctionnement standard acceptées par la ISED avec l'appareil
transmettant à son niveau de puissance certifié le plus élevé dans toutes les bandes de fréquences testées, bien que
le SAR soit déterminé au niveau de puissance certifié le plus élevé, le SAR réel le niveau de l'appareil pendant le
fonctionnement peut être bien en dessous de la valeur maximale. Avant qu'un nouveau modèle ne soit disponible à la
vente au public, il doit être testé et certifié à la ISED qu'il ne dépasse pas la limite d'exposition établie par la ISED, les
essais pour chaque produit sont effectués dans des positions et des emplacements comme exigé par la ISED. Pour le
fonctionnement à main levée, cet appareil a été testé et conforme aux directives d'exposition ISED RF lorsqu'il est utilisé
avec un accessoire désigné pour ce produit ou lorsqu'il est utilisé avec un acces Sory qui ne contient pas de métal.
54