Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and refri-
gerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock..
e) When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be control-
led with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's ope-
ration. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazar-
dous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Safety instructions Electric heater
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
The machine must be plugged to 230 V with 16
A fuse.
Switch the machine off and unplug it when unattended.
Caution: Some parts of the device may be very hot and
cause burns. Particular caution is recommended when
children and persons that must be protected are present.
Check all screw and plug-in connections and
protective equipment if firm and tightened
properly and whether all moving parts are
running smooth whenever the appliance is to be
put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
The appliance must not be used if damaged
or safety equipment is defective. Replace any
worn-out and damaged parts.
Before use check machine, cable, and plug for any dama-
ges or material fatigue. Repairs should only be carried out
by authorised Service Agents.
•
When using the appliance, it is essential to always
comply with the relevant local building and fire
regulations, appropriate electrical protection and
regulations of professional associations.
•
Ensure a safe distance from flammable items.
•
Free air inlet and outlet must always be provided.
•
Never put any foreign items into the appliance.
•
The appliance must never be covered during
operation.
•
The safety equipment must not be bridged or
blocked.
•
The appliance must never be directly under a wall
socket during operation.
ENGLISH
19
Publicité
Table des Matières
