Cleaning And Maintenance; Prevention Of Domestic Accidents; In The Event Of Problems - TEFAL KO6931 Mode D'emploi

6. THE KETTLE WILL SWITCH OFF AUTOMATICALLY
As soon as the water reaches boiling point or the chosen temperature.
• Do not leave water in the kettle after use as this quickens the formation of scale.

CLEANING AND MAINTENANCE

CLEANING YOUR KETTLE
Unplug it.
Let it cool down and clean it with a damp sponge.
• Never immerse the kettle, its base, the cord or the electric plug in water: the electrical
connections or the switch must not come into contact with water.
• Do not use scouring pads.
• Do not wipe the display while plugged in, it may cause unexpected start-up.
CLEANING THE FILTER*
The removable filter consists of a mesh to retain the particles of scale and prevent them falling
into your cup when pouring. This filter neither treats nor removes the hardness of the water. It
thus conserves all the qualities of the water. With very hard water, the filter can clog very quickly
(10 to 15 uses). It is important to clean it regularly. Sometimes the scale will not detach itself; it
will then need descaling.
DE-SCALING
De-scale regularly, preferably at least once a month or more frequently if your water is very hard.
Temperature detection in the kettle may be affected by limescale.
To de-scale your kettle:
• Using white vinegar which can be bought from hardware stores:
– Fill the kettle with ½ litre of white vinegar,
– Leave to stand for 1 hour without heating.
• Using citric acid:
– Boil ½ litre of water,
– Add 25 g of citric acid and leave to stand for 15 min.
• Empty your kettle and rinse 5 or 6 times. Repeat if necessary.
To de-scale your filter*:
Soak the filter in white vinegar or diluted citric acid.
• Never use a de-scaling method other than that recommended.

IN THE EVENT OF PROBLEMS

THERE IS NO EVIDENT DAMAGE TO YOUR KETTLE
• The kettle does not work
– Check that your kettle is properly connected.
– The kettle has been switched on without water or an accumulation of scale has caused the
overheat cut-out to operate: allow the kettle to cool and fill it with water. Descale first if scale
has accumulated.
Switch it on: the kettle should start working again after about 15 minutes.
* according to models
12
IF YOUR KETTLE HAS BEEN DROPPED, IF IT LEAKS OR IF THERE IS VISIBLE DAMAGE TO THE
POWER CORD, THE PLUG OR THE BASE OF THE KETTLE
Return your kettle to your After-Sales Service Centre, only they are authorised to carry out repairs.
See the guarantee conditions and list of centres in the booklet supplied with your kettle. The type
and serial number are shown on the bottom of your kettle. This guarantee covers manufacturing
defects and domestic use only. Any breakage or damage resulting from failure to comply with the
instructions for use is not covered by the guarantee.
• The manufacturer reserves the right to modify the characteristics or components of its kettles at
any time in the interests of the consumer.
• Do not use the kettle if damaged. No attempt must be made to dismantle the kettle or its
safety devices.
• If the supply cord is damaged, it must be replaced by the manufacturer, its after-sales service
centre or a similarly qualified person, in order to avoid any danger.

PREVENTION OF DOMESTIC ACCIDENTS

For a child, a burn or scald, even if slight, can sometimes be serious.
As they grow up, teach your children to beware of hot liquids to be found in the kitchen. Position
the kettle and its supply cord well to the rear of the work surface, out of the reach of children.
If an accident does occur, run cold water over the scald immediately and call a doctor if necessary.
• In order to avoid any accident: do not carry your child or baby at the same time as drinking or
carrying a hot drink.
Malfunction description
Kettle does not start heating The kettle is not positioned
correctly on the power base.
Kettle is heating but the Connection issue with the
control panel lights are off. indication lights and/or the
indicator light is damaged.
display "E0" Temperature sensor failure.
display "E1" Temperature sensor failure.
display "E3" Temperature regulation error.
Causes Solutions
Reposition the kettle on the
power base.
Send to an authorised service
centre for repair.
Send to an authorised service
centre for repair.
Send to an authorised service
centre for repair.
Switch off and unplug the
kettle for 1 minute, then plug
in and switch the kettle on
again. If the problem repeats,
please send to an authorised
service centre for repair.
13
EN