VISIOMED bewell connect MyTens Manuel De L'utilisateur page 15

RF emissions Group 1
CISPR 11
RF emissions
Class B
CISPR 11
Harmonic emissions
Class A
IEC 61000-3-2
Voltage fluctuations/
Complies
flicker emissions
IEC 61000-3-3
GUIDANCE AND MANUFACTURE'S DECLARATION – ELECTROMAGNETIC IMMUNITY
The BW-TSX / TS1 is intended for use in the electromagnetic environment specified below.
The customer or the user of BW-TSX / TS1 should assure that it is used in such an
environment.
IMMUNITY IEC 60601 TEST
LEVEL
TEST
Electrostatic ±6 kV contact
discharge ±8 kV air
(ESD)
IEC
61000-4-2
Electrical fast ±2 kV for power
transient/burst supply lines
IEC ±1 kV for input/
61000-4-4 output lines
28 BewellConnect - BW-TSX/BW-TS1 - User Manual - 11-2017v2
The BW-TSX / TS1 use RF
energy only for its internal
function. Therefore, its
RF emissions are very low
and are not likely to cause
any interference in nearby
electronic equipment.
The BW-TSX / TS1 is suitable
for use in all establishments,
including domestic
establishments and those
directly connected to the
public low-voltage power
supply network that supplies
buildings used for domestic
purposes.
COMPLIANCE ELECTROMAGNE
LEVEL TIC ENVIRONMENT
- GUIDANCE
±8 kV contact Floors should be
±15 kV air wood, concrete or
ceramic tile. If floor
are covered with
synthetic material,
the relative humidity
should be at least
30%.
±2kV for power Mains power quality
supply lines should be that of a
typical commercial
or hospital
environment.
Surge ± 1 kV line(s) to
IEC line(s)
61000-4-5 ± 2 kV line(s) to
earth
Voltage dips, <5% U
T
short (>95% dip in U
T
interruptions for 0.5 cycle
and voltage 40% U
T
variations on power (60% dip in U )
T
supply input lines for 5 cycles
IEC 61000-4-11 70% U
T
(30% dip in U )
T
for 25 cycles
<5% U
T
(>95% dip in U
T
for 5 sec
Power 3 A/m
frequency
(50Hz/60Hz)
magnetic field
IEC
61000-4-8
NOTE UT is the a.c. mains voltage prior to application of the test level.
GUIDANCE AND MANUFACTURE'S DECLARATION – ELECTROMAGNETIC IMMUNITY
The BW-TSX / TS1 is intended for use in the electromagnetic environment specified below.
The customer or the user of the BW-TSX / TS1 should assure that it is used in such an
environment.
IMMUNITY IEC 60601 TEST
LEVEL
TEST
BewellConnect - BW-TSX/BW-TS1 - User Manual - 11-2017v2
±1 kV differential Mains power quality
mode should be that of a
typical commercial
or hospital
environment.
<5% U Mains power quality
T
) (>95% dip in U ) should be that of a
T
for 0.5 cycle typical commercial
40% U or hospital
T
(60% dip in U ) environment. If the
T
for 5 cycles user of the BW-TSX
70% U / TS1 requires
T
(30% dip in U ) continued operation
T
for 25 cycles during power mains
<5% U interruptions, it is
T
) (>95% dip in U ) recommended that
T
for 5 sec the BW-TSX / TS1
be powered from
an uninterruptible
power supply or a
battery.
30 A/m Power frequency
magnetic fields
should be at levels
characteristic of a
typical location in a
typical commercial
or hospital
environment.
COMPLIANCE ELECTROMAGNETIC
LEVEL ENVIRONMENT - GUIDANCE
29